Grundig 5008

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Grundig 5008

Art Hoch
Senior Member

Posts: 403
Threads: 40
Joined: Feb 2011
City: McPherson, KS

#16

07-28-2014, 08:00 PM

Restoration not going so good. Set receives FM well, SW sporadically, BC never. Cleaned band switches the best I can. They are NOT easy to get to. Guess I'll have to have my radio buddy in town bring his signal generator over and see what we can see. Without dial stringing couldn't select stations anyway unless I leave the back off and that's problematical with a plug/power source integrated into the back.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Grundig 5008 - by Art Hoch - 07-16-2014, 11:51 AM

RE: Grundig 5008 - by morzh - 07-16-2014, 04:26 PM

RE: Grundig 5008 - by Art Hoch - 07-16-2014, 06:08 PM

RE: Grundig 5008 - by morzh - 07-16-2014, 08:46 PM

RE: Grundig 5008 - by Art Hoch - 07-20-2014, 09:14 AM

RE: Grundig 5008 - by Arran - 07-20-2014, 02:04 PM

RE: Grundig 5008 - by Art Hoch - 07-20-2014, 03:54 PM

RE: Grundig 5008 - by codefox1 - 07-20-2014, 10:13 PM

RE: Grundig 5008 - by Art Hoch - 07-20-2014, 11:27 PM

RE: Grundig 5008 - by gregb - 07-20-2014, 11:41 PM

RE: Grundig 5008 - by morzh - 07-20-2014, 11:48 PM

RE: Grundig 5008 - by Arran - 07-21-2014, 03:26 AM

RE: Grundig 5008 - by Art Hoch - 07-21-2014, 11:19 PM

RE: Grundig 5008 - by Art Hoch - 07-22-2014, 12:44 PM

RE: Grundig 5008 - by Art Hoch - 07-26-2014, 05:43 PM

RE: Grundig 5008 - by Art Hoch - 07-28-2014, 08:00 PM

RE: Grundig 5008 - by morzh - 07-28-2014, 11:05 PM

RE: Grundig 5008 - by Art Hoch - 07-29-2014, 11:18 AM

RE: Grundig 5008 - by morzh - 07-29-2014, 12:10 PM

RE: Grundig 5008 - by Art Hoch - 07-30-2014, 05:34 PM

RE: Grundig 5008 - by Arran - 07-30-2014, 08:08 PM

RE: Grundig 5008 - by Art Hoch - 07-31-2014, 10:46 AM

RE: Grundig 5008 - by Art Hoch - 08-04-2014, 09:16 PM

RE: Grundig 5008 - by murf - 08-06-2014, 08:02 PM

RE: Grundig 5008 - by Art Hoch - 08-08-2014, 08:35 PM

RE: Grundig 5008 - by murf - 08-08-2014, 09:00 PM

RE: Grundig 5008 - by Art Hoch - 08-09-2014, 10:20 PM

RE: Grundig 5008 - by Art Hoch - 08-09-2014, 10:24 PM

RE: Grundig 5008 - by Ron Ramirez - 08-10-2014, 07:25 AM

RE: Grundig 5008 - by Art Hoch - 08-13-2014, 06:06 PM

RE: Grundig 5008 - by Art Hoch - 08-22-2014, 02:24 PM

RE: Grundig 5008 - by Art Hoch - 08-29-2014, 12:41 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

Who's Online

There are currently 6908 online users. [Complete List]
» 2 Member(s) | 6906 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me