1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 38-7CS
Bob Andersen
Phorum Expert
*****
Posts: 797
Threads: 42
Joined: Dec 2008
City: Chicago, IL
#21

07-28-2014, 10:29 PM
I rechecked the tubes with my Hickok 600A and one was marginal but the other test like new with no gas. The Zenith 6K7 that works well has almost identical readings Icon_crazy The only other tube tester I have with settings for a 6K7 is an I-177B but it's in storage right now.
(This post was last modified: 07-28-2014, 10:30 PM by Bob Andersen.)
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 38-7CS - by Bob Andersen - 07-24-2014, 07:32 PM
RE: Philco 38-7CS - by Bob Andersen - 07-24-2014, 07:41 PM
RE: Philco 38-7CS - by Bob Andersen - 07-24-2014, 07:48 PM
RE: Philco 38-7CS - by Bob Andersen - 07-24-2014, 07:57 PM
RE: Philco 38-7CS - by Arran - 07-24-2014, 09:34 PM
RE: Philco 38-7CS - by Bob Andersen - 07-24-2014, 09:50 PM
RE: Philco 38-7CS - by codefox1 - 07-25-2014, 01:34 PM
RE: Philco 38-7CS - by Chuck Schwark - 07-25-2014, 01:46 PM
RE: Philco 38-7CS - by morzh - 07-25-2014, 01:47 PM
RE: Philco 38-7CS - by Bob Andersen - 07-25-2014, 04:24 PM
RE: Philco 38-7CS - by morzh - 07-25-2014, 05:02 PM
RE: Philco 38-7CS - by Arran - 07-26-2014, 12:06 AM
RE: Philco 38-7CS - by Bob Andersen - 07-27-2014, 03:35 PM
RE: Philco 38-7CS - by gregb - 07-27-2014, 11:13 PM
RE: Philco 38-7CS - by Bob Andersen - 07-27-2014, 11:28 PM
RE: Philco 38-7CS - by Bob Andersen - 07-28-2014, 04:16 PM
RE: Philco 38-7CS - by Mondial - 07-28-2014, 04:26 PM
RE: Philco 38-7CS - by Bob Andersen - 07-28-2014, 05:18 PM
RE: Philco 38-7CS - by Mondial - 07-28-2014, 05:36 PM
RE: Philco 38-7CS - by Bob Andersen - 07-28-2014, 06:51 PM
RE: Philco 38-7CS - by Bob Andersen - 07-28-2014, 10:29 PM
RE: Philco 38-7CS - by Chuck Schwark - 07-29-2014, 10:35 AM
RE: Philco 38-7CS - by morzh - 07-29-2014, 10:37 AM
RE: Philco 38-7CS - by Chuck Schwark - 07-29-2014, 10:42 AM
RE: Philco 38-7CS - by morzh - 07-29-2014, 11:02 AM
RE: Philco 38-7CS - by Warren - 07-29-2014, 01:59 PM
RE: Philco 38-7CS - by gregb - 07-29-2014, 03:16 PM
RE: Philco 38-7CS - by Bob Andersen - 07-29-2014, 03:31 PM
RE: Philco 38-7CS - by Bob Andersen - 08-03-2014, 02:06 PM
RE: Philco 38-7CS - by codefox1 - 08-03-2014, 04:29 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration