Philco 42-1010 Dial Stringing

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 42-1010 Dial Stringing

Jon Scaptura
Junior Member

Posts: 22
Threads: 10
Joined: Nov 2005

12-13-2005, 10:23 AM

Chuck Schwark Wrote:The dial cord stringing diagram was also not published in the original Philco service bulletin for this model either. But the 1009 and 1011, 1012 were published. Go figure!?

Chuck,
Are any of those chassis strung the same at the 1010? I was trying to match the diagrams up to my 1010, but it looks like my set needs two seperate loops of dial string, rather than one string. Can anyone confirm? I have the pointer for my set, but the mice did away with whatever string was once threaded through the pullies.

Jon Scaptura
Workbench webcam
My Radios

Website Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 42-1010 Dial Stringing - by Jon Scaptura - 12-12-2005, 07:38 PM

[No subject] - by Terry Judkins - 12-13-2005, 12:24 AM

[No subject] - by Chuck Schwark - 12-13-2005, 09:55 AM

[No subject] - by Jon Scaptura - 12-13-2005, 10:23 AM

[No subject] - by Chuck Schwark - 12-13-2005, 11:58 AM

[No subject] - by Ron Ramirez - 12-13-2005, 01:30 PM

[No subject] - by Jon Scaptura - 12-13-2005, 04:45 PM

[No subject] - by Ron Ramirez - 12-13-2005, 05:58 PM

[No subject] - by Ron Ramirez - 12-13-2005, 06:53 PM

[No subject] - by Chuck Schwark - 12-13-2005, 08:16 PM

Thanks - by Jon Scaptura - 12-13-2005, 11:36 PM

View a Printable Version

Users browsing this thread: 4 Guest(s)

Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

Who's Online

There are currently 6616 online users. [Complete List]
» 5 Member(s) | 6611 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me