Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 70 Reproduction Cabinet
#48

Any knob is better than a pair of pliers, but the little vise-grips work pretty well.

Yeah I like the cabinets too but I still think you should put your name on the units that are sold complete, but not the parts. I think that this was done on the previous production(s). Not a brass plaque on the front but a mark on the bottom of the base. If it doesn't make any difference, like people have said, then it should be no problem taking credit for them.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/


Messages In This Thread
Philco 70 Reproduction Cabinet - by Steve Davis - 08-02-2014, 08:36 PM
RE: Philco 70 Reproduction Cabinet - by morzh - 08-02-2014, 09:31 PM
RE: Philco 70 Reproduction Cabinet - by gregb - 08-02-2014, 10:18 PM
RE: Philco 70 Reproduction Cabinet - by Arran - 08-02-2014, 10:23 PM
RE: Philco 70 Reproduction Cabinet - by Arran - 08-02-2014, 11:40 PM
RE: Philco 70 Reproduction Cabinet - by tab10672 - 08-03-2014, 12:31 AM
RE: Philco 70 Reproduction Cabinet - by Arran - 08-03-2014, 12:45 AM
RE: Philco 70 Reproduction Cabinet - by codefox1 - 08-03-2014, 04:23 PM
RE: Philco 70 Reproduction Cabinet - by morzh - 08-03-2014, 05:20 PM
RE: Philco 70 Reproduction Cabinet - by Arran - 08-04-2014, 08:32 PM
RE: Philco 70 Reproduction Cabinet - by morzh - 08-05-2014, 11:11 AM
RE: Philco 70 Reproduction Cabinet - by Arran - 08-06-2014, 01:32 AM
RE: Philco 70 Reproduction Cabinet - by morzh - 08-06-2014, 10:11 AM
RE: Philco 70 Reproduction Cabinet - by morzh - 08-06-2014, 10:35 AM
RE: Philco 70 Reproduction Cabinet - by Arran - 08-06-2014, 08:16 PM
RE: Philco 70 Reproduction Cabinet - by JimZ - 08-10-2014, 10:12 AM
RE: Philco 70 Reproduction Cabinet - by David - 08-10-2014, 11:38 AM
RE: Philco 70 Reproduction Cabinet - by morzh - 08-11-2014, 03:46 PM
RE: Philco 70 Reproduction Cabinet - by morzh - 08-11-2014, 04:03 PM
RE: Philco 70 Reproduction Cabinet - by morzh - 08-11-2014, 04:19 PM
RE: Philco 70 Reproduction Cabinet - by Phlogiston - 08-11-2014, 09:17 PM
RE: Philco 70 Reproduction Cabinet - by morzh - 08-11-2014, 09:24 PM
RE: Philco 70 Reproduction Cabinet - by tab10672 - 08-12-2014, 09:18 AM
RE: Philco 70 Reproduction Cabinet - by Arran - 08-12-2014, 10:50 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Philco 16B Parts
The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM
Philco 38-7 Speaker
I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM

[-]
Who's Online
There are currently no members online.

>