Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Rosin solution recipe
#11

You could always rub up baseballs with it.

Paul

Tubetalk1


Messages In This Thread
Rosin solution recipe - by Art Hoch - 08-12-2014, 09:56 PM
RE: Rosin solution recipe - by morzh - 08-12-2014, 10:07 PM
RE: Rosin solution recipe - by Warren - 08-12-2014, 11:49 PM
RE: Rosin solution recipe - by JimZ - 08-13-2014, 09:29 AM
RE: Rosin solution recipe - by GarySP - 08-13-2014, 10:16 AM
RE: Rosin solution recipe - by David - 08-13-2014, 10:23 AM
RE: Rosin solution recipe - by Paul Philco322 - 08-13-2014, 05:25 PM
RE: Rosin solution recipe - by morzh - 08-13-2014, 05:48 PM
RE: Rosin solution recipe - by codefox1 - 08-15-2014, 01:40 AM
RE: Rosin solution recipe - by Art Hoch - 08-15-2014, 02:31 PM
RE: Rosin solution recipe - by Paul Philco322 - 08-15-2014, 05:42 PM
RE: Rosin solution recipe - by Pffester - 03-07-2015, 11:36 AM
RE: Rosin solution recipe - by morzh - 03-07-2015, 12:15 PM
RE: Rosin solution recipe - by Pffester - 03-07-2015, 01:18 PM
RE: Rosin solution recipe - by David - 03-07-2015, 01:52 PM
RE: Rosin solution recipe - by Pffester - 03-07-2015, 02:06 PM



Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
Apparently there is a new Philco Repair Bench found at https://philcoradio.com/repairbench/ When I try to go to order a ...dconant — 12:00 PM
Philco 60 Squealing
Well, a wave trap is a trimmer in series with the coil so at the resonant frequency it provides a short to ground. This ...RodB — 10:07 AM
Philco 60 Squealing
Rod, My radio is run 7. The wave trap is on that schematic as shown in the picture. dconant — 09:21 AM
American Bosch Model 802 auto radio
Hi Arran ,  Thanks for your help with this radio.And especial thanks for letting me know to look it up under United Ame...Antipodal — 04:32 AM
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM

[-]
Who's Online
There are currently 6533 online users. [Complete List]
» 1 Member(s) | 6532 Guest(s)
Avatar

>