Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 90 Dial movement
#1

After restoiration, my Philco 90 works very well. However, the dial is a little slippery. This is because the rubber roler that makes it turn is worn. I tried to adjust it, but it continues to slip a little sometimes, especially near the lower frequency end. Is there any paint or rubber coating I could use to make the metal wheel adjust better to the rubber shaft?

Thanks Icon_rolleyes


Messages In This Thread
Philco 90 Dial movement - by Guest - 10-02-2008, 02:21 PM
Re: Philco 90 Dial movement - by Chuck Schwark - 10-02-2008, 02:39 PM
Re: Philco 90 Dial movement - by etech - 10-12-2008, 10:01 AM
Re: Philco 90 Dial movement - by Ron Ramirez - 10-12-2008, 10:10 AM
Re: Philco 90 Dial movement - by etech - 10-12-2008, 06:50 PM
Re: Philco 90 Dial movement - by Ron Ramirez - 10-12-2008, 09:35 PM
Re: Philco 90 Dial movement - by Guest - 10-13-2008, 06:23 AM
Re: Philco 90 Dial movement - by etech - 10-13-2008, 07:26 AM
Re: Philco 90 Dial movement - by Ron Ramirez - 10-13-2008, 06:06 PM
Re: Philco 90 Dial movement - by Tim Tress - 11-13-2008, 08:14 PM



Users browsing this thread:
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently no members online.

>