The cabinet refinishing.

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

The cabinet refinishing.

fields 100
Member

Posts: 228
Threads: 64
Joined: Dec 2013
City: Northbrook, IL

#21

08-27-2014, 04:46 PM

The orifice size is about 1/8". I tried to put through the 1/8"bit, and it went slightly loose, but the cup is over 20 years old. Here is my 16B straight after spraying, no polishing involved.

[Image: http://i881.photobucket.com/albums/ac17/...69282b.jpg]

Find

« Next Oldest | Next Newest »

Messages In This Thread

The cabinet refinishing. - by fields 100 - 08-21-2014, 11:57 PM

RE: The cabinet refinishing. - by Arran - 08-22-2014, 02:47 AM

RE: The cabinet refinishing. - by Warren - 08-22-2014, 03:04 AM

RE: The cabinet refinishing. - by fields 100 - 08-22-2014, 07:46 AM

RE: The cabinet refinishing. - by OldRestorer - 08-22-2014, 07:52 AM

RE: The cabinet refinishing. - by fields 100 - 08-22-2014, 08:21 AM

RE: The cabinet refinishing. - by OldRestorer - 08-22-2014, 08:50 AM

RE: The cabinet refinishing. - by Warren - 08-22-2014, 09:48 PM

RE: The cabinet refinishing. - by fields 100 - 08-23-2014, 08:59 AM

RE: The cabinet refinishing. - by Warren - 08-23-2014, 03:32 PM

RE: The cabinet refinishing. - by fields 100 - 08-23-2014, 08:14 PM

RE: The cabinet refinishing. - by Warren - 08-24-2014, 12:21 AM

RE: The cabinet refinishing. - by fields 100 - 08-24-2014, 07:22 AM

RE: The cabinet refinishing. - by aab1991 - 03-02-2015, 01:00 AM

RE: The cabinet refinishing. - by Warren - 08-24-2014, 03:26 PM

RE: The cabinet refinishing. - by Geoff - 08-24-2014, 11:56 PM

RE: The cabinet refinishing. - by Warren - 08-25-2014, 01:15 AM

RE: The cabinet refinishing. - by Bob Andersen - 08-27-2014, 12:30 AM

RE: The cabinet refinishing. - by PhilcoJohn - 08-27-2014, 07:31 AM

RE: The cabinet refinishing. - by fields 100 - 08-27-2014, 08:29 AM

RE: The cabinet refinishing. - by Warren - 08-27-2014, 04:16 PM

RE: The cabinet refinishing. - by fields 100 - 08-27-2014, 04:46 PM

RE: The cabinet refinishing. - by Warren - 08-27-2014, 07:55 PM

RE: The cabinet refinishing. - by fields 100 - 08-27-2014, 09:31 PM

RE: The cabinet refinishing. - by Warren - 08-27-2014, 10:21 PM

RE: The cabinet refinishing. - by fields 100 - 08-28-2014, 08:04 AM

RE: The cabinet refinishing. - by Phlogiston - 08-28-2014, 10:04 AM

RE: The cabinet refinishing. - by fields 100 - 08-28-2014, 03:01 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

Who's Online

There are currently 4807 online users. [Complete List]
» 2 Member(s) | 4805 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me