1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Test Equipment
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
What type of component is this?
mainewolverine
New Member
*
Posts: 2
Threads: 1
Joined: May 2014
City: Maine
#1

09-01-2014, 07:21 PM
I'm restoring a 1976 Mercury 204 "Drugstore" tube tester. I have a schematic which may be from an earlier model and shows a diode in the circuit where I found this component If this is a diode, I've never seen one like this. Does anyone have any ideas? It tested 1.8M ohm in one direction and 900K ohm in the other direction.

Thanks for any help.

Jim
   
   
   
Find
« Next Oldest | Next Newest »


Messages In This Thread
What type of component is this? - by mainewolverine - 09-01-2014, 07:21 PM
RE: What type of component is this? - by morzh - 09-01-2014, 10:14 PM
RE: What type of component is this? - by sam - 09-02-2014, 12:05 AM
RE: What type of component is this? - by tab10672 - 09-02-2014, 01:15 AM
RE: What type of component is this? - by sam - 09-02-2014, 12:25 PM
RE: What type of component is this? - by tab10672 - 09-02-2014, 01:07 PM
RE: What type of component is this? - by tab10672 - 09-02-2014, 03:28 PM
RE: What type of component is this? - by morzh - 09-02-2014, 04:37 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
IF can wire size and Rubber mounts?
Hello PHORUM members, I am still working on restoration of my PHILCO 37-640.  I want to start with rewiring the IF ca...georgetownjohn — 06:32 PM
Gilfillan Brothers Car Radio?
There is a Mission Bell model 19/19A that could be what you’re looking for, Riders vol 4. It has the tube line-up of: 0Z...Joe Rossi — 05:01 PM
Looking for verification of correct schematic.
Definitely 870044RossH — 01:12 PM
12' Philco
Wonder if the chassis was big too.daveone23 — 12:38 PM
Philco 38-2 Automatic Tuning
Hi Ron, I have sent Radio Daze my concerns with the dial so I guess we will see. They used my original to make the repro...dconant — 12:27 PM
Hickok AC51 tube tester
How does the  5W4 and 83 tube filaments get fed?martinj — 12:25 PM
462ron
Hi Dan, your original dial appears to be lighter, easier to allow light through. My original is similar except it’s crac...462ron — 12:07 PM
Philco 38-2 Automatic Tuning
I received my new 38-2 dial. I'm a little disappointed. As you can see in the picture the blues have a white shadow. The...dconant — 11:13 AM
Philco 38-2 Low Volume
I have been playing my 38-2 for a while now and it is doing very well. I did have to replace the 6A8 (osc) as it develop...dconant — 11:03 AM
Philco Speaker Spider
Hello, Does anyone with a 3 D printer make the spiders for those old Philco speakers? That might be a good idea for some...dconant — 09:41 AM

[-]
Who's Online
There are currently 3321 online users. [Complete List]
» 1 Member(s) | 3320 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Test Equipment