Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Bucking transformer possibility?
#7

It may use a mains transformer on the inside, but there just isn't enough information to tell, it does appear to have a metal case which most switchers would not have, it also lists the input line frequency which many switchers do not care about. At $2.54, and free shipping, you could buy one and find out, just remember that it's Chinese and it's rated at 60 watts, so assume that it's good up to 45-50 watts without burning up. I have no need of such things, I have a bin full of power cubes/wall warts that are from the era before China junk electronics.
Regards
Arran


Messages In This Thread
Bucking transformer possibility? - by ccomer1955 - 09-03-2014, 03:00 PM
RE: Bucking transformer possibility? - by Mondial - 09-03-2014, 03:37 PM
RE: Bucking transformer possibility? - by morzh - 09-03-2014, 03:52 PM
RE: Bucking transformer possibility? - by morzh - 09-04-2014, 08:50 AM
RE: Bucking transformer possibility? - by Arran - 09-04-2014, 11:43 PM
RE: Bucking transformer possibility? - by morzh - 09-04-2014, 11:54 PM
RE: Bucking transformer possibility? - by Arran - 09-05-2014, 01:52 AM
RE: Bucking transformer possibility? - by morzh - 09-05-2014, 09:04 AM
RE: Bucking transformer possibility? - by Arran - 09-06-2014, 02:50 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 610B oscillator wiring
Do you know what run # your chassis is? It took me a while to find what you were basing updates/modification on as I did...Radioroslyn — 07:34 AM
Need to purchase some accessories for restoration of my Old Philco Radio
COLLEAGUES, Thank you all for such good and important suggestions as how to find good replacement parts. I will go fo...palonso — 07:05 AM
Zenith H725
Here's what the inside of AM IFT2 looked like, and the other pic shows the discs I made to take place of the mica and ke...EdHolland — 07:40 PM
Zenith H725
IF2 will need replacement caps. The arcing was severe enough that the mica is pitted and holed where the HT flashed over...EdHolland — 04:04 PM
My Philco 37-116 Restore
Measuring from center tap like the tube voltages show. Cap 127 is isolated from ground. Cap 127 shown in upper left of p...dconant — 08:05 AM
My Philco 37-116 Restore
Are you measuring relative to the centertap or the GND?morzh — 11:57 PM
Philco 610B oscillator wiring
Still not clear on the wiring interface between the 6A7 and oscillator. After refering to the available schematics and s...Tubester — 07:18 PM
Refinishing Ideas
My 37-116 code 121 is the best sounding radio i have...a daily driver. Since we are talking about "changes". ...poulsbobill — 07:18 PM
My Philco 37-116 Restore
Hello, I finally got brave enough to take the cans off the Expander Unit. Got the grid cap wires replaced and back toget...dconant — 06:50 PM
Zenith H725
I got into the first AM IF can today, and found its mica was cracked. Amazing that it was still working. This one makes ...EdHolland — 06:10 PM

[-]
Who's Online
There are currently 864 online users. [Complete List]
» 3 Member(s) | 861 Guest(s)
AvatarAvatarAvatar

>