37 620 decal

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

37 620 decal

morzh
Odobenus rosmarus

Posts: 15,816
Threads: 554
Joined: Oct 2011
City: Jackson, NJ

#17

09-06-2014, 11:00 PM

I would leave it be too! Good 'nuff.

As for the center, the "I" is a bit left off the center, but a bit closer to it then "L".

However if you look at the letters, "LCO" Is quite a bit wider than "PHI" and so to keep it symmetrical "L" should be with its pole on or even a bit left off the center.
I guess it can get complicated.

Again, Kirk, it is good. Leave it where it is.

Find

« Next Oldest | Next Newest »

Messages In This Thread

37 620 decal - by OldRestorer - 09-04-2014, 01:07 PM

RE: 37 620 decal - by Ron Ramirez - 09-04-2014, 06:21 PM

RE: 37 620 decal - by OldRestorer - 09-04-2014, 06:27 PM

RE: 37 620 decal - by morzh - 09-04-2014, 06:49 PM

RE: 37 620 decal - by OldRestorer - 09-05-2014, 12:15 PM

RE: 37 620 decal - by Ron Ramirez - 09-05-2014, 12:19 PM

RE: 37 620 decal - by OldRestorer - 09-05-2014, 12:23 PM

RE: 37 620 decal - by OldRestorer - 09-05-2014, 12:54 PM

RE: 37 620 decal - by Ron Ramirez - 09-05-2014, 12:59 PM

RE: 37 620 decal - by OldRestorer - 09-05-2014, 01:14 PM

RE: 37 620 decal - by Ron Ramirez - 09-05-2014, 01:19 PM

RE: 37 620 decal - by morzh - 09-05-2014, 01:45 PM

RE: 37 620 decal - by codefox1 - 09-06-2014, 09:33 AM

RE: 37 620 decal - by Ron Ramirez - 09-06-2014, 10:25 PM

RE: 37 620 decal - by morzh - 09-06-2014, 10:28 PM

RE: 37 620 decal - by Ron Ramirez - 09-06-2014, 10:33 PM

RE: 37 620 decal - by morzh - 09-06-2014, 11:00 PM

RE: 37 620 decal - by sam - 09-07-2014, 12:40 AM

RE: 37 620 decal - by OldRestorer - 09-07-2014, 02:30 PM

RE: 37 620 decal - by Ron Ramirez - 09-08-2014, 05:45 AM

RE: 37 620 decal - by OldRestorer - 09-08-2014, 07:52 AM

RE: 37 620 decal - by morzh - 09-08-2014, 08:43 AM

RE: 37 620 decal - by OldRestorer - 09-08-2014, 09:59 AM

View a Printable Version

Users browsing this thread: 4 Guest(s)

Recent Posts
Philco 42-1008 conversion kit
I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit. That would rem...alangard — 09:30 PM
HiFi (Chifi) tube amp build - but my own design.
Tim Well...a chassis is metal. Magnetic or not, it does not matter. A transformer has some hum to it. It is natural. Th...morzh — 08:40 PM
Hickok AC51 tube tester
I thought the 83 tube was bad because it looked white but it tests strong. Blue gassy though. I checked the fuse, it was...martinj — 08:37 PM
Shadow Meter Bulb
Ross I am not sure what current limiting effect the incandescent provides. They are two different parts of the sch...morzh — 08:31 PM
12' Philco
Bob Thanks for that photo. I have been looking for it, and I cannot find anythinmg on the web. I forgot it was here...morzh — 08:29 PM
Shadow Meter Bulb
I think after all has been said, I will use the same bulb that is specified for the dial pilot light which is a #55. I ...georgetownjohn — 07:31 PM
12' Philco
There was also this Philco! klondike98 — 07:25 PM
HiFi (Chifi) tube amp build - but my own design.
I expected a challenge and this is just part of it. But, it's also supposed to be fun, entertaining, informative and enj...TV MAN — 07:12 PM
Shadow Meter Bulb
Butting in here with a question. Since the shadow meter is connected directly to the 1st and 2nd I.F.'s wouldn't the met...RossH — 06:43 PM
HiFi (Chifi) tube amp build - but my own design.
Mike, Tim; you are about to enter the twilight zone. Doo doo doo doo, doo doo doo doo This is something alright. I'm go...RodB — 06:26 PM

Who's Online

There are currently 5948 online users. [Complete List]
» 1 Member(s) | 5947 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me