PHILCO 98 EXPORT Model

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

PHILCO 98 EXPORT Model

HOTWIRE
Member

Posts: 62
Threads: 8
Joined: Oct 2012
City: County Kerry, Ireland

#22

09-09-2014, 08:19 PM

Thank you Ron.
I recon that resolves the matter.
Don't know if I can recover this one yet. It has been got at by the salt environment here. Not good for the coils etc.
The Cabinet is also full of lodgers. The speaker is kaput, no shadow meter. I will know more when I ohm out the rest.

The other one (the 640) is allllmost finished. It is singing away fine now Just finishing the cabinet.
I will report back soon as it is finished.

Regards.
Willie.

Find

« Next Oldest | Next Newest »

Messages In This Thread

PHILCO 98 EXPORT Model - by HOTWIRE - 10-08-2012, 01:50 PM

RE: PHILCO 98 EXPORT Model - by TA Forbes - 10-08-2012, 10:33 PM

RE: PHILCO 98 EXPORT Model - by HOTWIRE - 10-13-2012, 09:44 AM

RE: PHILCO 98 EXPORT Model - by HOTWIRE - 10-13-2012, 09:53 AM

RE: PHILCO 98 EXPORT Model - by TA Forbes - 10-14-2012, 08:55 AM

RE: PHILCO 98 EXPORT Model - by Ron Ramirez - 10-14-2012, 09:17 AM

RE: PHILCO 98 EXPORT Model - by Ron Ramirez - 10-14-2012, 11:01 AM

RE: PHILCO 98 EXPORT Model - by TA Forbes - 10-14-2012, 09:26 PM

RE: PHILCO 98 EXPORT Model - by Arran - 10-14-2012, 11:02 PM

RE: PHILCO 98 EXPORT Model - by HOTWIRE - 10-15-2012, 03:18 PM

RE: PHILCO 98 EXPORT Model - by Ron Ramirez - 10-15-2012, 04:23 PM

RE: PHILCO 98 EXPORT Model - by HOTWIRE - 10-15-2012, 07:18 PM

RE: PHILCO 98 EXPORT Model - by HOTWIRE - 03-12-2013, 11:27 AM

RE: PHILCO 98 EXPORT Model - by Ron Ramirez - 03-15-2013, 02:04 PM

RE: PHILCO 98 EXPORT Model - by HOTWIRE - 03-15-2013, 11:14 PM

RE: PHILCO 98 EXPORT Model - by Ron Ramirez - 03-17-2013, 01:08 PM

RE: PHILCO 98 EXPORT Model - by HOTWIRE - 03-19-2013, 09:09 AM

RE: PHILCO 98 EXPORT Model - by HOTWIRE - 09-09-2014, 06:02 PM

RE: PHILCO 98 EXPORT Model - by HOTWIRE - 09-09-2014, 06:06 PM

RE: PHILCO 98 EXPORT Model - by HOTWIRE - 09-09-2014, 06:13 PM

RE: PHILCO 98 EXPORT Model - by Ron Ramirez - 09-09-2014, 06:47 PM

RE: PHILCO 98 EXPORT Model - by HOTWIRE - 09-09-2014, 08:19 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

Who's Online

There are currently 3631 online users. [Complete List]
» 1 Member(s) | 3630 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me