Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Got a 39-6 today
#2

So the two damages are in those creases both sides of the cabinet.
Otherwise, the veneer is good, and the chassis is clean.

   

In fact he says it is working and they were using it until very recently and he said he forgot his inverter, so I said I had one in my car, and he was eager to demo it to me, but I said that I'd rather inspect it at home first before plugging it in.

Hey, I do not need it to work, and for 20 bucks in this condition I do not care if it does, I will recap etc no matter what.


Messages In This Thread
Got a 39-6 today - by morzh - 09-13-2014, 03:20 PM
RE: Got a 39-6 today - by morzh - 09-13-2014, 03:25 PM
RE: Got a 39-6 today - by sam - 09-13-2014, 07:59 PM
RE: Got a 39-6 today - by Ron Ramirez - 09-13-2014, 08:38 PM
RE: Got a 39-6 today - by morzh - 09-13-2014, 08:43 PM
RE: Got a 39-6 today - by Ron Ramirez - 09-13-2014, 08:53 PM
RE: Got a 39-6 today - by morzh - 09-13-2014, 09:07 PM
RE: Got a 39-6 today - by BenWA - 09-14-2014, 12:21 AM
RE: Got a 39-6 today - by morzh - 09-14-2014, 10:07 AM
RE: Got a 39-6 today - by klondike98 - 09-14-2014, 12:10 PM
RE: Got a 39-6 today - by morzh - 09-14-2014, 05:18 PM
RE: Got a 39-6 today - by PhilcoJohn - 09-14-2014, 06:55 PM
RE: Got a 39-6 today - by morzh - 09-14-2014, 07:17 PM
RE: Got a 39-6 today - by Arran - 09-16-2014, 01:30 AM
RE: Got a 39-6 today - by Jake Blake - 01-01-2020, 10:27 PM
RE: Got a 39-6 today - by Tubeglow20 - 01-02-2020, 12:10 AM
RE: Got a 39-6 today - by rfeenstra - 01-02-2020, 12:46 AM
RE: Got a 39-6 today - by morzh - 01-02-2020, 11:01 AM
RE: Got a 39-6 today - by Radioroslyn - 01-02-2020, 11:42 AM
RE: Got a 39-6 today - by Jake Blake - 01-02-2020, 11:21 PM
RE: Got a 39-6 today - by Tubeglow20 - 01-03-2020, 01:45 AM
RE: Got a 39-6 today - by Jake Blake - 01-03-2020, 09:26 AM
RE: Got a 39-6 today - by Radioroslyn - 01-03-2020, 12:33 PM
RE: Got a 39-6 today - by Jake Blake - 01-03-2020, 01:30 PM
RE: Got a 39-6 today - by Phlogiston - 01-03-2020, 02:04 PM
RE: Got a 39-6 today - by Radioroslyn - 01-03-2020, 02:05 PM
RE: Got a 39-6 today - by Jake Blake - 01-03-2020, 02:53 PM
RE: Got a 39-6 today - by Jake Blake - 01-03-2020, 03:01 PM
RE: Got a 39-6 today - by klondike98 - 01-03-2020, 05:12 PM
RE: Got a 39-6 today - by Phlogiston - 01-03-2020, 07:31 PM
RE: Got a 39-6 today - by Jake Blake - 01-03-2020, 08:15 PM
RE: Got a 39-6 today - by Tubeglow20 - 01-03-2020, 10:17 PM
RE: Got a 39-6 today - by Jake Blake - 01-04-2020, 12:14 AM
RE: Got a 39-6 today - by Art Hoch - 01-07-2020, 11:26 AM
RE: Got a 39-6 today - by Jake Blake - 01-07-2020, 11:52 AM
RE: Got a 39-6 today - by Ron Ramirez - 01-07-2020, 09:33 PM
RE: Got a 39-6 today - by Jake Blake - 01-08-2020, 07:48 AM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently 4499 online users. [Complete List]
» 2 Member(s) | 4497 Guest(s)
AvatarAvatar

>