1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Starting on Philco 20 Deluxe.
morzh
Odobenus rosmarus
*****
Posts: 15,825
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
#8

09-21-2014, 10:11 PM
Finished recap-recarb.
Would be it for testing, I have the filter block connected, though the can has not been cleaned yet but that is not needed for now.
However when starting on the chassis I saw the volume pot touched up, and I see the sectios have been swapped. The 250 Ohm section (the back one) is connected to GND and ANT, and the 5K section is biasing RF cathodes. The tell-tell sign, the GND strip is soldered to the back section. Should be the front one.

mañana....
(This post was last modified: 09-21-2014, 10:12 PM by morzh.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
Starting on Philco 20 Deluxe. - by morzh - 09-14-2014, 11:52 AM
RE: Starting on Philco 20 Deluxe. - by morzh - 09-14-2014, 05:21 PM
RE: Starting on Philco 20 Deluxe. - by morzh - 09-14-2014, 07:10 PM
RE: Starting on Philco 20 Deluxe. - by morzh - 09-14-2014, 09:27 PM
RE: Starting on Philco 20 Deluxe. - by morzh - 09-21-2014, 10:11 PM
RE: Starting on Philco 20 Deluxe. - by morzh - 09-23-2014, 09:10 PM
RE: Starting on Philco 20 Deluxe. - by morzh - 09-25-2014, 12:05 PM
RE: Starting on Philco 20 Deluxe. - by morzh - 10-15-2014, 11:01 PM
RE: Starting on Philco 20 Deluxe. - by Arran - 10-16-2014, 12:51 AM
RE: Starting on Philco 20 Deluxe. - by morzh - 10-16-2014, 11:50 AM
RE: Starting on Philco 20 Deluxe. - by morzh - 10-16-2014, 10:54 PM
RE: Starting on Philco 20 Deluxe. - by morzh - 10-17-2014, 04:00 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

[-]
Who's Online
There are currently 5094 online users. [Complete List]
» 1 Member(s) | 5093 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration