Output Transformer for Model 41-300

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Output Transformer for Model 41-300

rck46
Member

Posts: 53
Threads: 21
Joined: Apr 2006
City: Davis, CA

09-23-2014, 06:17 PM

I just started working on a 41-300 and came across this thread when I found that the primary on my output transformer is also open. In addition to the use of a Hammond HX-125D as a replacement would this Edcor also be suitable? see/www.edcorusa.com/gxpp10-4-10k. The Edcor is less costly. Does anyone have any experience with the Edcor products? Regardless of which one is used I will need some guidance on working around the secondary feedback tap referred to earlier in this thread.

Thanks, Bob

Find

« Next Oldest | Next Newest »

Messages In This Thread

Output Transformer for Model 41-300 - by hyounce - 08-31-2010, 11:48 PM

RE: Output Transformer for Model 41-300 - by rck46 - 09-23-2014, 06:17 PM

RE: Output Transformer for Model 41-300 - by Arran - 09-24-2014, 12:25 AM

RE: Output Transformer for Model 41-300 - by morzh - 09-24-2014, 01:15 PM

RE: Output Transformer for Model 41-300 - by codefox1 - 09-24-2014, 11:45 PM

RE: Output Transformer for Model 41-300 - by Arran - 09-25-2014, 12:42 AM

RE: Output Transformer for Model 41-300 - by rck46 - 09-25-2014, 01:41 PM

RE: Output Transformer for Model 41-300 - by rck46 - 09-26-2014, 01:05 PM

Re: Output Transformer for Model 41-300 - by Ron Ramirez - 09-01-2010, 07:29 AM

Re: Output Transformer for Model 41-300 - by hyounce - 09-01-2010, 10:31 AM

Re: Output Transformer for Model 41-300 - by Ron Ramirez - 09-01-2010, 10:38 AM

Re: Output Transformer for Model 41-300 - by hyounce - 09-01-2010, 12:51 PM

Re: Output Transformer for Model 41-300 - by Ron Ramirez - 09-01-2010, 02:34 PM

Re: Output Transformer for Model 41-300 - by hyounce - 09-01-2010, 05:36 PM

Re: Output Transformer for Model 41-300 - by mgutierres - 09-04-2010, 07:44 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

Who's Online

There are currently 3906 online users. [Complete List]
» 1 Member(s) | 3905 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me