1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 89 Detector Coil
radiodale
Member
***
Posts: 93
Threads: 20
Joined: Aug 2014
City: Greenville, TX
#9

09-30-2014, 10:01 PM
Signal is greater at the 77 grid. Oscillator dead, can anyone guess the cause? Correct, the Oscillator coil is bad. Yes, the tickler that I have read about. Took the coil out, verified the open, counted the turns with a needle (tedious) and measured the wire size to be #36. Will wind tomorrow. Thank you for the help.
Dale


http://www.dalesantiqueradio.com/
(This post was last modified: 10-01-2014, 09:13 AM by radiodale. Edit Reason: typo )
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 89 Detector Coil - by radiodale - 09-27-2014, 08:23 PM
RE: Philco 89 Oscillator Coil - by morzh - 09-27-2014, 08:35 PM
RE: Philco 89 Oscillator Coil - by radiodale - 09-27-2014, 09:12 PM
RE: Philco 89 Oscillator Coil - by morzh - 09-27-2014, 09:58 PM
RE: Philco 89 Detector Coil - by radiodale - 09-29-2014, 05:13 PM
RE: Philco 89 Detector Coil - by morzh - 09-29-2014, 08:55 PM
RE: Philco 89 Detector Coil - by radiodale - 09-29-2014, 09:59 PM
RE: Philco 89 Detector Coil - by radiodale - 09-30-2014, 10:01 PM
RE: Philco 89 Detector Coil - by radiodale - 10-02-2014, 09:53 PM
RE: Philco 89 Detector Coil - by mikethedruid - 10-02-2014, 11:08 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 6361 online users. [Complete List]
» 1 Member(s) | 6360 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration