Tube Shield for Philco 38-15

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Tube Shield for Philco 38-15

klondike98
Phorum Moderator

Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR

09-30-2014, 10:54 PM

Welcome to the Phorum! If you look on John Kendall's site, go to "Parts" and search on 38-15 you'll see he has a rusted parts chassis. You might write him and see if he's got a tube shield for you. A couple other places to try to find a replacement are found here. You can put a "Wanted" ad in this Phorum in the "Wanted" section as well. (You can also fabricate one.)

Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page

Website Find

« Next Oldest | Next Newest »

Messages In This Thread

Tube Shield for Philco 38-15 - by w2rik - 09-30-2014, 06:14 PM

RE: Tube Shield for Philco 38-15 - by sam - 09-30-2014, 07:43 PM

RE: Tube Shield for Philco 38-15 - by Radioroslyn - 09-30-2014, 09:44 PM

RE: Tube Shield for Philco 38-15 - by w2rik - 09-30-2014, 10:12 PM

RE: Tube Shield for Philco 38-15 - by klondike98 - 09-30-2014, 10:54 PM

RE: Tube Shield for Philco 38-15 - by Radioroslyn - 10-01-2014, 07:06 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

Who's Online

There are currently 3885 online users. [Complete List]
» 2 Member(s) | 3883 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me