38-2670 cabinet problem

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

38-2670 cabinet problem

murf
Senior Member

Posts: 668
Threads: 144
Joined: Jun 2011
City: Elko,MN.

10-01-2014, 08:02 PM

Well fella's, I started to work on the corners today.
Started by sanding down the crack to see what was underneath.
Did not find that the wood under the crack had any signs of cracking.
I will attempt to re-veneer the 2 corner sections.
I have a piece of walnut veneer that should do both corners.
Made a clamping block with the 3/4 inch radius incorpoated into it. Should help keep the new veneer nice and tight while glue sets up.
Wish me luck.
murf
[Image: http://i1161.photobucket.com/albums/q509...eneer1.jpg]
[Image: http://i1161.photobucket.com/albums/q509...eneer2.jpg]

(This post was last modified: 10-03-2014, 06:11 PM by murf.)

Find

« Next Oldest | Next Newest »

Messages In This Thread

38-2670 cabinet problem - by murf - 09-27-2014, 03:46 PM

RE: 37-675 cabinet problem - by sam - 09-27-2014, 04:25 PM

RE: 37-675 cabinet problem - by OldRestorer - 09-27-2014, 08:51 PM

RE: 37-675 cabinet problem - by OldRestorer - 09-28-2014, 03:07 PM

RE: 37-675 cabinet problem - by murf - 09-28-2014, 04:19 PM

RE: 38-2670 cabinet problem - by Arran - 09-30-2014, 09:47 PM

RE: 38-2670 cabinet problem - by murf - 10-01-2014, 08:02 PM

RE: 38-2670 cabinet problem - by murf - 10-03-2014, 06:18 PM

RE: 38-2670 cabinet problem - by Ron Ramirez - 10-03-2014, 06:37 PM

RE: 38-2670 cabinet problem - by PhilcoJohn - 10-03-2014, 07:25 PM

RE: 38-2670 cabinet problem - by murf - 10-03-2014, 09:31 PM

RE: 38-2670 cabinet problem - by Arran - 10-04-2014, 11:08 PM

RE: 38-2670 cabinet problem - by Eliot Ness - 10-05-2014, 07:52 AM

RE: 38-2670 cabinet problem - by Arran - 10-07-2014, 11:43 PM

RE: 38-2670 cabinet problem - by murf - 10-08-2014, 01:32 PM

RE: 38-2670 cabinet problem - by thirtiesradio - 10-09-2014, 12:38 AM

RE: 38-2670 cabinet problem - by murf - 10-26-2014, 03:01 PM

RE: 38-2670 cabinet problem - by sam - 10-26-2014, 03:29 PM

RE: 38-2670 cabinet problem - by Eliot Ness - 10-26-2014, 03:36 PM

RE: 38-2670 cabinet problem - by klondike98 - 10-26-2014, 03:46 PM

RE: 38-2670 cabinet problem - by thirtiesradio - 10-26-2014, 10:16 PM

RE: 38-2670 cabinet problem - by jerryhawthorne - 10-27-2014, 02:12 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Shadow Meter Bulb
Any 6.3 volt pilot light will work. I would use the brightest one I could find in my workroom. Be sure the dial is clean...RodB — 10:45 AM
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM

Who's Online

There are currently 7900 online users. [Complete List]
» 3 Member(s) | 7897 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me