1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
38-2670 cabinet problem
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#9

10-03-2014, 06:37 PM
Okay, I'm supposed to be taking some time off but since no one else chimed in, I'll say something...

Great save! Icon_thumbup I see the new veneer has the grain running vertical rather than horizontal, but in the long run, that might be a good thing due to the curves.
--
Ron Ramirez
Ferdinand IN
Find
« Next Oldest | Next Newest »


Messages In This Thread
38-2670 cabinet problem - by murf - 09-27-2014, 03:46 PM
RE: 37-675 cabinet problem - by sam - 09-27-2014, 04:25 PM
RE: 37-675 cabinet problem - by OldRestorer - 09-27-2014, 08:51 PM
RE: 37-675 cabinet problem - by OldRestorer - 09-28-2014, 03:07 PM
RE: 37-675 cabinet problem - by murf - 09-28-2014, 04:19 PM
RE: 38-2670 cabinet problem - by Arran - 09-30-2014, 09:47 PM
RE: 38-2670 cabinet problem - by murf - 10-01-2014, 08:02 PM
RE: 38-2670 cabinet problem - by murf - 10-03-2014, 06:18 PM
RE: 38-2670 cabinet problem - by Ron Ramirez - 10-03-2014, 06:37 PM
RE: 38-2670 cabinet problem - by PhilcoJohn - 10-03-2014, 07:25 PM
RE: 38-2670 cabinet problem - by murf - 10-03-2014, 09:31 PM
RE: 38-2670 cabinet problem - by Arran - 10-04-2014, 11:08 PM
RE: 38-2670 cabinet problem - by Eliot Ness - 10-05-2014, 07:52 AM
RE: 38-2670 cabinet problem - by Arran - 10-07-2014, 11:43 PM
RE: 38-2670 cabinet problem - by murf - 10-08-2014, 01:32 PM
RE: 38-2670 cabinet problem - by thirtiesradio - 10-09-2014, 12:38 AM
RE: 38-2670 cabinet problem - by murf - 10-26-2014, 03:01 PM
RE: 38-2670 cabinet problem - by sam - 10-26-2014, 03:29 PM
RE: 38-2670 cabinet problem - by Eliot Ness - 10-26-2014, 03:36 PM
RE: 38-2670 cabinet problem - by klondike98 - 10-26-2014, 03:46 PM
RE: 38-2670 cabinet problem - by thirtiesradio - 10-26-2014, 10:16 PM
RE: 38-2670 cabinet problem - by jerryhawthorne - 10-27-2014, 02:12 PM



Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Any 6.3 volt pilot light will work. I would use the brightest one I could find in my workroom. Be sure the dial is clean...RodB — 10:45 AM
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM

[-]
Who's Online
There are currently 7820 online users. [Complete List]
» 3 Member(s) | 7817 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration