Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

GE M 65 Volume issues
#4

According to this schematic, it does look like a 250K with a loudness tap. Tap isn't super critical.

As far as your volume issue, check to make sure your pot has continuity (250K across the outer terminals), and check R13, 850 ohms, to make sure it's good. I suspect it's gone a ways up in value, and since it looks like a bias resistor for the tube as well as the ground return for the volume control it could be giving you problems.

Also check R10 and R11 (both 1M ohm) as these are in your AVC circuit and almost assuredly have gone up in value. I've seen these go as much as 500% high, or open.


Messages In This Thread
GE M 65 Volume issues - by jph14 - 10-02-2014, 07:18 PM
RE: GE M 65 Volume issues - by Radioroslyn - 10-02-2014, 09:35 PM
RE: GE M 65 Volume issues - by jph14 - 10-03-2014, 03:38 PM
RE: GE M 65 Volume issues - by BrendaAnnD - 10-03-2014, 09:23 PM
RE: GE M 65 Volume issues - by jph14 - 10-04-2014, 05:52 AM
RE: GE M 65 Volume issues - by jph14 - 10-12-2014, 12:44 PM
RE: GE M 65 Volume issues - by jph14 - 10-21-2014, 01:05 PM



Users browsing this thread:
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently no members online.

>