Model 610 bakelite block

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Model 610 bakelite block

Kestas
Member

Posts: 177
Threads: 19
Joined: Feb 2014
City: The Motor City,Detroit MI

10-05-2014, 10:31 AM

Thanks, Terry. This is a table model. Waiting in the queue are three consoles --- 37-620, 90, 91, and a tabletop 20. I'm hooked. 35 years ago I restored a fully working 42-1013, that now needs a full electronic restoration.

(This post was last modified: 10-05-2014, 10:32 AM by Kestas.)

Find

« Next Oldest | Next Newest »

Messages In This Thread

Model 610 bakelite block - by Kestas - 10-04-2014, 07:26 PM

RE: Model 610 bakelite block - by radiohenry - 10-04-2014, 07:37 PM

RE: Model 610 bakelite block - by klondike98 - 10-04-2014, 08:00 PM

RE: Model 610 bakelite block - by Radioroslyn - 10-04-2014, 08:22 PM

RE: Model 610 bakelite block - by Kestas - 10-05-2014, 10:10 AM

RE: Model 610 bakelite block - by Radioroslyn - 10-05-2014, 10:20 AM

RE: Model 610 bakelite block - by Kestas - 10-05-2014, 10:31 AM

RE: Model 610 bakelite block - by Radioroslyn - 10-05-2014, 12:46 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

Who's Online

There are currently 3602 online users. [Complete List]
» 2 Member(s) | 3600 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me