Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Newbie
#7

(10-05-2014, 12:46 PM)Radioroslyn Wrote:  Hi Pat Welcome to the Phorum!
Have done that many times.
Good luck in you search and restoration
Those set have an undesirable feature,
there fill with decomposing rubber
wire. Most Philcos from'39-42 do.
Terry

Thanks Terry.
I figured I would have to rewire the entire chassis anyway, as well as replace caps and resistors. Gives me something to do over the winter.

Pat


Messages In This Thread
Newbie - by Patrick - 10-05-2014, 09:29 AM
RE: Newbie - by sam - 10-05-2014, 11:22 AM
RE: Newbie - by Paul Philco322 - 10-05-2014, 11:53 AM
RE: Newbie - by Patrick - 10-05-2014, 12:14 PM
RE: Newbie - by Radioroslyn - 10-05-2014, 12:46 PM
RE: Newbie - by Patrick - 10-05-2014, 01:33 PM
RE: Newbie - by NostalgiaRadioTime - 10-05-2014, 01:00 PM
RE: Newbie - by Patrick - 10-05-2014, 01:38 PM
RE: Newbie - by Art Hoch - 10-07-2014, 10:55 AM
RE: Newbie - by PhilcoJohn - 10-07-2014, 05:32 PM
RE: Newbie - by Patrick - 10-07-2014, 06:32 PM
RE: Newbie - by klondike98 - 10-08-2014, 05:19 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Help with Readrite 410 tube tester
I fixed it. The filament selector switch is not that great of quality. Cleaned it and it takes some fiddling with to get...daveone23 — 06:58 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a vacuum tube set and it's over 60 years old.  My uncle acquired it for my parents when Philco was done with it, an...jeibner — 10:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Hi J Eibner, Welcome to the Phorum.  Lots of Phriendly Pholks with Phine (See a pattern here?) advice. It is very...MrFixr55 — 09:54 PM
Philco 89B code 123 newbie
Or you can do what Terry suggests. Thx Terry for remembering that. A lot cheaper. I remember an article about that, b...MrFixr55 — 09:07 PM
Philco 48-200 alignment questions
Thanks to everybody for all the info so far. RodB, thanks for the additional info. I worked on this radio years ago a...transitony — 08:40 PM
Philco 89B code 123 newbie
Now that I've been thinking about it somewhere I saw a replacement made using a section of pvc pipe and a cap to cover t...Radioroslyn — 08:25 PM
Philco 48-200 alignment questions
Terry's gimmick cap is two insulated wires twisted together about 2 inches long, one wire attaches to the generator outp...RodB — 07:46 PM
Philco 48-200 alignment questions
Hi, in this case I would be certain that pin 7, which is B-, of the 14A7 is not "hot". If it is then reverse t...RodB — 07:39 PM
Philco 48-200 alignment questions
Yup. The gimmick is to take the place of the 100mmfd cap you don't have.Radioroslyn — 07:34 PM
Philco 48-200 alignment questions
Thanks for the reply Terry. Yes I am definitely using an isolation transformer. If I work with your method and connec...transitony — 07:29 PM

[-]
Who's Online
There are currently no members online.

>