38-2670 cabinet problem

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

38-2670 cabinet problem

murf
Senior Member

Posts: 668
Threads: 144
Joined: Jun 2011
City: Elko,MN.

#15

10-08-2014, 01:32 PM

I think the veneer turned out pretty good, now I just have to fabricate some new trim to replace the old half missing trim pieces.
Think I will use my woodworking skills to saw,sand the 2 front pieces with the 3/4 inch radius versus trying to bend some trim around those corners.
Will post pics before I re-finish.
Out of town for 10 days visiting family in AZ.
Probably keep this one when it's done,so I am not concerned if the finished radio is not an exact clone of the original.
murf

Find

« Next Oldest | Next Newest »

Messages In This Thread

38-2670 cabinet problem - by murf - 09-27-2014, 03:46 PM

RE: 37-675 cabinet problem - by sam - 09-27-2014, 04:25 PM

RE: 37-675 cabinet problem - by OldRestorer - 09-27-2014, 08:51 PM

RE: 37-675 cabinet problem - by OldRestorer - 09-28-2014, 03:07 PM

RE: 37-675 cabinet problem - by murf - 09-28-2014, 04:19 PM

RE: 38-2670 cabinet problem - by Arran - 09-30-2014, 09:47 PM

RE: 38-2670 cabinet problem - by murf - 10-01-2014, 08:02 PM

RE: 38-2670 cabinet problem - by murf - 10-03-2014, 06:18 PM

RE: 38-2670 cabinet problem - by Ron Ramirez - 10-03-2014, 06:37 PM

RE: 38-2670 cabinet problem - by PhilcoJohn - 10-03-2014, 07:25 PM

RE: 38-2670 cabinet problem - by murf - 10-03-2014, 09:31 PM

RE: 38-2670 cabinet problem - by Arran - 10-04-2014, 11:08 PM

RE: 38-2670 cabinet problem - by Eliot Ness - 10-05-2014, 07:52 AM

RE: 38-2670 cabinet problem - by Arran - 10-07-2014, 11:43 PM

RE: 38-2670 cabinet problem - by murf - 10-08-2014, 01:32 PM

RE: 38-2670 cabinet problem - by thirtiesradio - 10-09-2014, 12:38 AM

RE: 38-2670 cabinet problem - by murf - 10-26-2014, 03:01 PM

RE: 38-2670 cabinet problem - by sam - 10-26-2014, 03:29 PM

RE: 38-2670 cabinet problem - by Eliot Ness - 10-26-2014, 03:36 PM

RE: 38-2670 cabinet problem - by klondike98 - 10-26-2014, 03:46 PM

RE: 38-2670 cabinet problem - by thirtiesradio - 10-26-2014, 10:16 PM

RE: 38-2670 cabinet problem - by jerryhawthorne - 10-27-2014, 02:12 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 16B Parts
The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM
Philco 38-7 Speaker
I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone, As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me