1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
variable capacitor
exray
Phorum Expert
*****
Posts: 893
Threads: 9
Joined: Mar 2008
City: Vieques, PR USA State, Province, Country: PR
#5

10-08-2014, 09:14 PM
   



Apart from the horseshoe clips, these rotor plates need a bending tweak.
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
variable capacitor - by Pillo69 - 10-08-2014, 05:47 PM
RE: variable capacitor - by Radioroslyn - 10-08-2014, 05:53 PM
RE: variable capacitor - by Pillo69 - 10-08-2014, 07:04 PM
RE: variable capacitor - by Joeztech - 10-08-2014, 08:15 PM
RE: variable capacitor - by exray - 10-08-2014, 09:14 PM
RE: variable capacitor - by Kestas - 10-09-2014, 04:36 PM
RE: variable capacitor - by morzh - 10-09-2014, 07:55 PM
RE: variable capacitor - by Pillo69 - 10-10-2014, 06:00 PM
RE: variable capacitor - by morzh - 10-10-2014, 09:20 PM
RE: variable capacitor - by AI2V - 10-11-2014, 10:54 AM
RE: variable capacitor - by Pillo69 - 10-11-2014, 05:41 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration