Dead as a doornail

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Dead as a doornail

ODPILOT
Member

Posts: 122
Threads: 37
Joined: Jul 2012
City: Coral Springs, FL

#10

10-08-2014, 10:42 PM

I went back to it and looked at it again. The the two terminals at the back of the control read 7 ohms. The middle set of terminals (3 of them) read about 300 Khoms (not ohms). And the other set of terminals read very low ohms.
This is starting to look like a switch problem I believe. Do they make replacement switches for these things or do I have to pull a working one out of another Philco? The Philco part # on this on/off switch is 33-5563-60 according to the schematic. On the switch itself, it says: Philco 137326. Thanks

Find

« Next Oldest | Next Newest »

Messages In This Thread

Dead as a doornail - by ODPILOT - 10-08-2014, 02:32 PM

RE: Dead as a doornail - by morzh - 10-08-2014, 03:57 PM

RE: Dead as a doornail - by ODPILOT - 10-08-2014, 05:12 PM

RE: Dead as a doornail - by Radioroslyn - 10-08-2014, 06:02 PM

RE: Dead as a doornail - by morzh - 10-08-2014, 08:16 PM

RE: Dead as a doornail - by ODPILOT - 10-08-2014, 08:51 PM

RE: Dead as a doornail - by ODPILOT - 10-08-2014, 09:03 PM

RE: Dead as a doornail - by morzh - 10-08-2014, 09:45 PM

RE: Dead as a doornail - by BrendaAnnD - 10-08-2014, 10:09 PM

RE: Dead as a doornail - by ODPILOT - 10-08-2014, 10:42 PM

RE: Dead as a doornail - by morzh - 10-08-2014, 11:46 PM

RE: Dead as a doornail - by ODPILOT - 10-09-2014, 09:32 PM

RE: Dead as a doornail - by morzh - 10-09-2014, 10:04 PM

RE: Dead as a doornail - by ODPILOT - 10-10-2014, 07:58 AM

RE: Dead as a doornail - by morzh - 10-10-2014, 09:19 PM

RE: Dead as a doornail - by ODPILOT - 10-12-2014, 08:10 PM

RE: Dead as a doornail - by Arran - 10-12-2014, 08:38 PM

RE: Dead as a doornail - by morzh - 10-12-2014, 09:26 PM

RE: Dead as a doornail - by ODPILOT - 10-13-2014, 09:11 AM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

Who's Online

There are currently 3992 online users. [Complete List]
» 2 Member(s) | 3990 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me