1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
49-905 IF Transformer disassembly question
OZ4
Senior Member
****
Posts: 285
Threads: 27
Joined: Nov 2012
City: Tehachapi. California
#4

10-10-2014, 12:12 AM
 Yes I found the tabs on the base of the can. Thanks. The xformer I have checked seems to tune pretty well on the scope so now I am nit picking the small caps that this thing has all through the oscillator and rf section along with the resistors.

My problem now is the Riders schematic seems to have some discrepancies in it. I found the 12AU6 pinout has a mis print. And the radio some extra parts. My radio must have revisions in it.
Any place I can find a more accurate one? I seem to remember some saying that one could be ordered that is a much better copy.
This thing is a 49-905 121
Thanks
Chris
!!!!!!!!!!!!!!!!!!!RESISTANCE IS FUTILE!!!!!!!!!!!!!!!!!!!!!!  
                           /\/\/\/\/\/\/\/\/\
                                                     
                                 [Image: http://philcoradio.com/phorum/images/smi...on_eek.gif]  Chris
Find
« Next Oldest | Next Newest »


Messages In This Thread
RE: 49-905 IF Transformer disassembly question - by OZ4 - 10-10-2014, 12:12 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

[-]
Who's Online
There are currently 3610 online users. [Complete List]
» 2 Member(s) | 3608 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration