1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Dead as a doornail
ODPILOT
Member
***
Posts: 122
Threads: 37
Joined: Jul 2012
City: Coral Springs, FL
#14

10-10-2014, 07:58 AM
That is the schematic you have it right. I looked at the continuity across the power cord plug prongs again however. On my GOOD radio, there IS continuity across the power cord prongs when the on/off switch is on. On this new one we are talking about - there is no continuity when the switch is on. I'll check out the filament string shortly, but my gut feeling at this point is that the switch may be fried. Thanks for your help.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Dead as a doornail - by ODPILOT - 10-08-2014, 02:32 PM
RE: Dead as a doornail - by morzh - 10-08-2014, 03:57 PM
RE: Dead as a doornail - by ODPILOT - 10-08-2014, 05:12 PM
RE: Dead as a doornail - by Radioroslyn - 10-08-2014, 06:02 PM
RE: Dead as a doornail - by morzh - 10-08-2014, 08:16 PM
RE: Dead as a doornail - by ODPILOT - 10-08-2014, 08:51 PM
RE: Dead as a doornail - by ODPILOT - 10-08-2014, 09:03 PM
RE: Dead as a doornail - by morzh - 10-08-2014, 09:45 PM
RE: Dead as a doornail - by BrendaAnnD - 10-08-2014, 10:09 PM
RE: Dead as a doornail - by ODPILOT - 10-08-2014, 10:42 PM
RE: Dead as a doornail - by morzh - 10-08-2014, 11:46 PM
RE: Dead as a doornail - by ODPILOT - 10-09-2014, 09:32 PM
RE: Dead as a doornail - by morzh - 10-09-2014, 10:04 PM
RE: Dead as a doornail - by ODPILOT - 10-10-2014, 07:58 AM
RE: Dead as a doornail - by morzh - 10-10-2014, 09:19 PM
RE: Dead as a doornail - by ODPILOT - 10-12-2014, 08:10 PM
RE: Dead as a doornail - by Arran - 10-12-2014, 08:38 PM
RE: Dead as a doornail - by morzh - 10-12-2014, 09:26 PM
RE: Dead as a doornail - by ODPILOT - 10-13-2014, 09:11 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 6283 online users. [Complete List]
» 1 Member(s) | 6282 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration