Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Also a newbie
#10

Thank you for the greetings. I appreciate it. I imagine vintage radio collecting could become a bit of a hobby. I hope that I will keep my new venture in proper balance! Now I will now peruse the 1957 product line in an attempt to acquire one that is from my wife's birth year. Any recommendations?
Thank you also, Ron, for steering me directly to the 1954 models. My radio certainly appears to be a B710 rather than the depicted B711.
I do have a question. On the Sessions Movement clock, mine has a plug, or a blank cover, at the six o'clock position, whereas on the B-711 model there is a knob. Any information on an additional feature that is not on my clock?
Many thanks,
Bill
Sonoma, CA


Messages In This Thread
Also a newbie - by bsteach@sbcglobal.net - 10-08-2014, 01:27 PM
RE: Also a newbie - by Ron Ramirez - 10-08-2014, 03:13 PM
RE: Also a newbie - by klondike98 - 10-08-2014, 05:13 PM
RE: Also a newbie - by morzh - 10-08-2014, 07:09 PM
RE: Also a newbie - by exray - 10-08-2014, 08:04 PM
RE: Also a newbie - by PhilcoJohn - 10-09-2014, 05:25 PM
RE: Also a newbie - by KCMike - 10-09-2014, 07:38 PM
RE: Also a newbie - by gregb - 10-09-2014, 10:20 PM
RE: Also a newbie - by bsteach@sbcglobal.net - 10-10-2014, 10:11 AM
RE: Also a newbie - by bsteach@sbcglobal.net - 10-10-2014, 10:40 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM

[-]
Who's Online
There are currently 3593 online users. [Complete List]
» 3 Member(s) | 3590 Guest(s)
AvatarAvatarAvatar

>