Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 38-116X vs RCA 15K
#15

(03-13-2013, 11:36 PM)morzh Wrote:  In   fact 1M resistor fix in an eye tube socket is an extremely easy fix and does not require opening the socket. I did that with my Zenith and I think I wrote how I did it.
It's my own invention. Icon_smile

If anyone's interested I can post it again.
Takes 10 minutes tops.

Hope you can help, not sure how old this message is, but I have the 15K too and I did replace the resistor in the socket, but it didn't help. What else can I check or change, the original resistor that I took out was good. Hope you can help me.


Messages In This Thread
Philco 38-116X vs RCA 15K - by Jayce - 03-13-2013, 04:19 PM
RE: Philco 38-116X vs RCA 15K - by y2kbruce - 03-13-2013, 04:47 PM
RE: Philco 38-116X vs RCA 15K - by Jayce - 03-13-2013, 05:04 PM
RE: Philco 38-116X vs RCA 15K - by Arran - 03-13-2013, 07:37 PM
RE: Philco 38-116X vs RCA 15K - by Jayce - 03-13-2013, 10:55 PM
RE: Philco 38-116X vs RCA 15K - by morzh - 03-13-2013, 11:36 PM
RE: Philco 38-116X vs RCA 15K - by OldJack1969 - 10-10-2014, 07:04 PM
RE: Philco 38-116X vs RCA 15K - by jontz - 03-14-2013, 07:14 AM
RE: Philco 38-116X vs RCA 15K - by morzh - 03-14-2013, 06:08 PM
RE: Philco 38-116X vs RCA 15K - by jontz - 03-14-2013, 09:28 PM
RE: Philco 38-116X vs RCA 15K - by Arran - 03-14-2013, 09:41 PM
RE: Philco 38-116X vs RCA 15K - by morzh - 03-14-2013, 09:51 PM
RE: Philco 38-116X vs RCA 15K - by Jayce - 03-14-2013, 10:58 PM
RE: Philco 38-116X vs RCA 15K - by morzh - 03-15-2013, 10:20 AM
RE: Philco 38-116X vs RCA 15K - by TA Forbes - 03-15-2013, 07:24 PM
RE: Philco 38-116X vs RCA 15K - by morzh - 10-10-2014, 09:27 PM
RE: Philco 38-116X vs RCA 15K - by thirtiesradio - 12-12-2014, 04:49 PM
RE: Philco 38-116X vs RCA 15K - by Arran - 12-13-2014, 02:10 AM
RE: Philco 38-116X vs RCA 15K - by Phlogiston - 12-13-2014, 09:07 PM
RE: Philco 38-116X vs RCA 15K - by thirtiesradio - 12-14-2014, 02:26 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently no members online.

>