1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
variable capacitor
AI2V
Member
***
Posts: 201
Threads: 26
Joined: Dec 2005
City: Morris Plains, NJ
#10

10-11-2014, 10:54 AM
(10-10-2014, 09:20 PM)morzh Wrote:  Looks sparkling!

I know it would be a pain but I would grind off the rivets that hold the forks, clean all of the surfaces (especially the cap frame where the fork makes contact), and put it back together using screws.  There's an awful lot of oxidation on the frame and it could make for a very noisy and intermittent tuning.  A Dremel tool with a small grinding will quickly cut the rivets.  The whole operation should take less than ten minutes.
Pete AI2V
Find
« Next Oldest | Next Newest »


Messages In This Thread
variable capacitor - by Pillo69 - 10-08-2014, 05:47 PM
RE: variable capacitor - by Radioroslyn - 10-08-2014, 05:53 PM
RE: variable capacitor - by Pillo69 - 10-08-2014, 07:04 PM
RE: variable capacitor - by Joeztech - 10-08-2014, 08:15 PM
RE: variable capacitor - by exray - 10-08-2014, 09:14 PM
RE: variable capacitor - by Kestas - 10-09-2014, 04:36 PM
RE: variable capacitor - by morzh - 10-09-2014, 07:55 PM
RE: variable capacitor - by Pillo69 - 10-10-2014, 06:00 PM
RE: variable capacitor - by morzh - 10-10-2014, 09:20 PM
RE: variable capacitor - by AI2V - 10-11-2014, 10:54 AM
RE: variable capacitor - by Pillo69 - 10-11-2014, 05:41 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

[-]
Who's Online
There are currently 5107 online users. [Complete List]
» 1 Member(s) | 5106 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration