Speaker woes

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Speaker woes

morzh
Odobenus rosmarus

Posts: 15,823
Threads: 554
Joined: Oct 2011
City: Jackson, NJ

10-13-2014, 10:13 PM

Looks to me like you said, someone really decided to drive the spooks out of the house and cranked the dBs.

I only saw this once, when someone plugged a movie projector speaker in a 220VAC outlet....the speaker vomited the cone right out across the room.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Speaker woes - by NostalgiaRadioTime - 10-13-2014, 05:21 PM

RE: Speaker woes - by jerryhawthorne - 10-13-2014, 07:01 PM

RE: Speaker woes - by NostalgiaRadioTime - 10-13-2014, 09:24 PM

RE: Speaker woes - by morzh - 10-13-2014, 10:13 PM

RE: Speaker woes - by Arran - 10-13-2014, 10:25 PM

RE: Speaker woes - by jerryhawthorne - 10-14-2014, 12:08 AM

RE: Speaker woes - by NostalgiaRadioTime - 10-14-2014, 12:26 AM

RE: Speaker woes - by BrendaAnnD - 10-14-2014, 04:52 AM

RE: Speaker woes - by NostalgiaRadioTime - 10-14-2014, 07:11 AM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

Who's Online

There are currently 3998 online users. [Complete List]
» 3 Member(s) | 3995 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me