1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Tickler coil for a 84B
varrojames
Junior Member
**
Posts: 10
Threads: 8
Joined: Oct 2014
City: CA
#1

10-20-2014, 04:36 PM
I am restoring an '34 Model 84B. I just replaced the 4 Meg ohm on the I.F. Trans with a new 2 Meg and a new grid lead(I just snipped out the old resistor rather than trying to unsolder). I noticed that the lead wire from the Tickler was just standing free with no connection. I created a small solder drop and managed to maneuver the end into the solder ball, hoping I would get a connection. The fine wire is also covered with a cloth wrapping so it made things a little more difficult.
So the question is: What if I have no connection to the tickler, what are consequences? You guys understand this re-gen stuff better than I do. How will I know if all is well when I get to the alignment phase? OR, should I just pull the thing and try and have it re-wound?
Thanks for any advice you can give me
The thankful receiver bears a plentiful harvest.
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Tickler coil for a 84B - by varrojames - 10-20-2014, 04:36 PM
RE: Tickler coil for a 84B - by klondike98 - 10-20-2014, 08:01 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently 2364 online users. [Complete List]
» 1 Member(s) | 2363 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration