38-2 tuning mech

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

38-2 tuning mech

doug-5er
Junior Member

Posts: 40
Threads: 6
Joined: Aug 2014
City: Lakewood, Ca 90713

#14

10-20-2014, 04:23 PM

Well the WD-40 freed it up,but there is still some contact inside the mech somewhere and i can't tell where it is.
I can hold the band switch and turn the dial freely, B4 it would only turn a small amount.Now i have full range
on the tuning cap,so i guess this is a good thing.I'm still a little leery about taking the mech apart,don't wanna
open a can of worms.

Find

« Next Oldest | Next Newest »

Messages In This Thread

38-2 tuning mech - by doug-5er - 10-18-2014, 01:11 PM

RE: 38-2 tuning mech - by sam - 10-18-2014, 01:31 PM

RE: 38-2 tuning mech - by morzh - 10-18-2014, 04:15 PM

RE: 38-2 tuning mech - by doug-5er - 10-18-2014, 05:13 PM

RE: 38-2 tuning mech - by morzh - 10-18-2014, 06:10 PM

RE: 38-2 tuning mech - by doug-5er - 10-18-2014, 07:09 PM

RE: 38-2 tuning mech - by morzh - 10-18-2014, 09:23 PM

RE: 38-2 tuning mech - by doug-5er - 10-18-2014, 09:29 PM

RE: 38-2 tuning mech - by Ron Ramirez - 10-19-2014, 07:29 AM

RE: 38-2 tuning mech - by doug-5er - 10-20-2014, 08:11 AM

RE: 38-2 tuning mech - by morzh - 10-20-2014, 08:32 AM

RE: 38-2 tuning mech - by doug-5er - 10-20-2014, 10:16 AM

RE: 38-2 tuning mech - by morzh - 10-20-2014, 11:14 AM

RE: 38-2 tuning mech - by doug-5er - 10-20-2014, 04:23 PM

RE: 38-2 tuning mech - by morzh - 10-20-2014, 06:24 PM

RE: 38-2 tuning mech - by doug-5er - 10-22-2014, 02:36 PM

RE: 38-2 tuning mech - by doug-5er - 01-31-2015, 10:45 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM
Jackson 665 j2 schematic request
Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
>>I'll write to the Henry Ford. I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM
Philco 48-200 alignment questions
Just checked the power cord and I did in fact wire it so the hot side (small prong) goes to the switch.transitony — 11:52 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
Thanks for the suggestions. I'll write to the Henry Ford. That would certainly make sense since by the time this prod...jeibner — 11:49 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
For what it's worth, the Henry Ford Museum and Greenfield Village in Dearborn, Michigan may be an option. The obvious ...GarySP — 11:39 AM
Help with Readrite 410 tube tester
Mike and I just had a short discussion yesterday about this very subject. So often it's the connections. Ya gotta have t...RodB — 10:08 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
We have a regional museum here in the Twin Cities called The Pavek Museum. They have an extensive collection of communic...RodB — 09:30 AM
Philco 89B code 123 newbie
I did some nosing around and found that the original caps were 4 3/4" long x 1 5/16" in dia. Guess what 1"...Radioroslyn — 09:28 AM

Who's Online

There are currently 3179 online users. [Complete List]
» 1 Member(s) | 3178 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me