1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 610 transformer open
morzh
Odobenus rosmarus
*****
Posts: 15,823
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
#9

10-22-2014, 02:39 PM
Kestas


Did you check your primary with across the AC plug or actual transformer wires?
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 610 transformer open - by Kestas - 10-22-2014, 10:11 AM
RE: Philco 610 transformer open - by morzh - 10-22-2014, 10:24 AM
RE: Philco 610 transformer open - by morzh - 10-22-2014, 10:33 AM
RE: Philco 610 transformer open - by Kestas - 10-22-2014, 11:00 AM
RE: Philco 610 transformer open - by sam - 10-22-2014, 12:21 PM
RE: Philco 610 transformer open - by Eliot Ness - 10-22-2014, 02:20 PM
RE: Philco 610 transformer open - by morzh - 10-22-2014, 02:28 PM
RE: Philco 610 transformer open - by morzh - 10-22-2014, 02:39 PM
RE: Philco 610 transformer open - by Kestas - 10-22-2014, 04:36 PM
RE: Philco 610 transformer open - by Kestas - 10-22-2014, 10:09 PM
RE: Philco 610 transformer open - by morzh - 10-23-2014, 10:55 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration