Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Dial restoration on a 38-14T
#4

 Radiodaze claims that they are working on reproducing gold foil dials, likely because they were used in many catalin sets, which unlike now were at the low end of the radio market. From what I can tell the gold is often a coating of orange shellac over top of an embossed aluminum foil, with paint added for the lettering and numbers, probably not with all but with many.
Regards
Arran


Messages In This Thread
Dial restoration on a 38-14T - by varrojames - 10-22-2014, 01:59 PM
RE: Dial restoration on a 38-14T - by Eliot Ness - 10-22-2014, 03:18 PM
RE: Dial restoration on a 38-14T - by Ron Ramirez - 10-22-2014, 09:32 PM
RE: Dial restoration on a 38-14T - by Arran - 10-22-2014, 09:50 PM
RE: Dial restoration on a 38-14T - by morzh - 10-23-2014, 11:03 AM
RE: Dial restoration on a 38-14T - by Steve D - 10-24-2014, 08:56 AM
RE: Dial restoration on a 38-14T - by Ron Ramirez - 10-24-2014, 10:11 AM
RE: Dial restoration on a 38-14T - by morzh - 10-24-2014, 10:18 AM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Not sure if anyone has tried this but there are 6.3 volt miniature lamps in bayonet and screw-in base options available ...GarySP — 11:31 AM
Shadow Meter Bulb
Any 6.3 volt pilot light will work. I would use the brightest one I could find in my workroom. Be sure the dial is clean...RodB — 10:45 AM
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM

[-]
Who's Online
There are currently 8409 online users. [Complete List]
» 2 Member(s) | 8407 Guest(s)
AvatarAvatar

>