Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

My Bakelite Peeve
#2

The Hippos (at least the 1946-48 models) are definitely Bakelite, and I suspect the 1949 Hippo is Bakelite as well.

With the exception of the 1938 ivory Plaskon 38-12CBI, 38-14CBI & 38-15CBI, all of the Philco table model sets made between 1938 and 1942 that are not in wood cabinets, are in Bakelite cabinets.

Postwar, Philco still made quite a few Bakelite models even into 1950 or so. Some of the postwar Philcos are non-Bakelite plastic, though; such as the 48-225, 48-230, 49-503, 50-620, 50-621, 51-629, 51-631...

--
Ron Ramirez
Ferdinand IN


Messages In This Thread
My Bakelite Peeve - by Uffda - 11-11-2008, 02:12 AM
Re: My Bakelite Peeve - by Ron Ramirez - 11-11-2008, 09:50 AM
Re: My Bakelite Peeve - by Uffda - 11-11-2008, 03:08 PM
Re: My Bakelite Peeve - by Syl - 11-11-2008, 04:42 PM
Re: My Bakelite Peeve - by Uffda - 11-11-2008, 06:09 PM
Re: My Bakelite Peeve - by exray - 11-11-2008, 06:51 PM
Re: My Bakelite Peeve - by Syl - 11-11-2008, 10:16 PM
Re: My Bakelite Peeve - by Syl - 11-11-2008, 10:24 PM
Re: My Bakelite Peeve - by Uffda - 11-11-2008, 10:48 PM
Re: My Bakelite Peeve - by Syl - 11-11-2008, 10:57 PM
Re: My Bakelite Peeve - by Uffda - 11-11-2008, 11:41 PM
Re: My Bakelite Peeve - by exray - 11-12-2008, 01:51 AM
Re: My Bakelite Peeve - by Uffda - 11-12-2008, 04:27 AM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5453 online users. [Complete List]
» 1 Member(s) | 5452 Guest(s)
Avatar

>