1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco Model 91 shadowmeter
Dave Slusarczyk
Junior Member
**
Posts: 32
Threads: 9
Joined: Jul 2008
City: Bossier City, LA
#3

11-13-2008, 12:16 AM
Thanks Ron,

I am at a loss as to the resistance measurement. I beleived it to be 40 gauge wire which I unspooled. I will double check.

I just have difficulty running the B+ through 40 gauge wire--or smaller. Seems as if one is torture testing the wire. Perhaps this is the reason I have seen a couple of sets with bad shadow meters-----

Thanks again Ron for the quick reply!!!

Dave
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco Model 91 shadowmeter - by Dave Slusarczyk - 11-12-2008, 11:51 PM
Re: Philco Model 91 shadowmeter - by Ron Ramirez - 11-13-2008, 12:00 AM
Re: Philco Model 91 shadowmeter - by Dave Slusarczyk - 11-13-2008, 12:16 AM
Re: Philco Model 91 shadowmeter - by etech - 11-13-2008, 12:30 AM
Re: Philco Model 91 shadowmeter - by etech - 11-13-2008, 09:44 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5121 online users. [Complete List]
» 2 Member(s) | 5119 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration