Help on 48-482 FM

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Help on 48-482 FM

jerryhawthorne
Phorum Expert

Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA

11-14-2008, 03:55 PM

This particular can has a single trimmer and an adjustable coil. The trimmer is not the normal type I am use to seeing. It is not the compression type with a mica insulator. It appears to me to be more like a wiper, perhaps a single turn? I have had the can off. I wish someone could take a look at the schematic and let me know if I am wrong in that the two wires coming out of the can from the oscillator side should read very low or infinite in circuit. It appears to me they should read infinite not just a few ohms as they do. Sorry, I don't know how to post the schematic from N/A on the forum.
Thanks for any help!
Jerry

A friend in need is a pest! Bill Slee ca 1970.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Help on 48-482 FM - by jerryhawthorne - 11-12-2008, 04:57 PM

Re: Help on 48-482 FM - by codefox1 - 11-14-2008, 02:42 PM

Re: Help on 48-482 FM - by jerryhawthorne - 11-14-2008, 03:55 PM

Re: Help on 48-482 FM - by jerryhawthorne - 11-15-2008, 10:00 PM

Re: Help on 48-482 FM - by Ron Ramirez - 11-16-2008, 03:13 PM

Re: Help on 48-482 FM - by jerryhawthorne - 11-16-2008, 08:35 PM

Re: Help on 48-482 FM - by Terry Judkins - 11-16-2008, 11:01 PM

Re: Help on 48-482 FM - by jerryhawthorne - 11-17-2008, 08:01 PM

Re: Help on 48-482 FM - by Terry Judkins - 11-17-2008, 08:27 PM

Re: Help on 48-482 FM - by jerryhawthorne - 11-18-2008, 10:01 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me