Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 37-604 Help Needed
#8

Welcome Dave,

I don't believe anyone makes a replacement for your transformer. The transformers in old radios are often referred to as unobtainium. Always be careful when working around one.
You can try to get a replacement off of eBay, or by posting an ad in the "Wanted Ads" section of the Phorum. You might also search for a donor chassis of the same type in order to retrieve the part you need.

It might also be possible to repair your transformer by replacing the broken lug. Might not look perfect, but if you can make it work electrically, you're probably good to go.

Good luck,
Jon


Messages In This Thread
Philco 37-604 Help Needed - by dseverson - 11-05-2014, 05:09 PM
RE: Philco 37-604 Help Needed - by klondike98 - 11-05-2014, 07:26 PM
RE: Philco 37-604 Help Needed - by Radioroslyn - 11-06-2014, 10:15 PM
RE: Philco 37-604 Help Needed - by morzh - 11-07-2014, 12:21 AM
RE: Philco 37-604 Help Needed - by dseverson - 11-07-2014, 01:34 AM
RE: Philco 37-604 Help Needed - by morzh - 11-07-2014, 10:42 AM
RE: Philco 37-604 Help Needed - by dseverson - 11-10-2014, 05:37 AM
RE: Philco 37-604 Help Needed - by PAradiogeek - 11-10-2014, 08:39 AM
RE: Philco 37-604 Help Needed - by Radioroslyn - 11-10-2014, 10:16 AM
RE: Philco 37-604 Help Needed - by dseverson - 11-18-2014, 07:10 PM
RE: Philco 37-604 Help Needed - by KCMike - 11-18-2014, 07:39 PM
RE: Philco 37-604 Help Needed - by klondike98 - 11-18-2014, 08:00 PM
RE: Philco 37-604 Help Needed - by mikethedruid - 11-19-2014, 08:11 AM
RE: Philco 37-604 Help Needed - by dseverson - 11-20-2014, 01:43 AM
RE: Philco 37-604 Help Needed - by PAradiogeek - 11-21-2014, 10:32 AM
RE: Philco 37-604 Help Needed - by dseverson - 11-22-2014, 06:11 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Zenith H725
Here's what the inside of AM IFT2 looked like, and the other pic shows the discs I made to take place of the mica and ke...EdHolland — 07:40 PM
Zenith H725
IF2 will need replacement caps. The arcing was severe enough that the mica is pitted and holed where the HT flashed over...EdHolland — 04:04 PM
My Philco 37-116 Restore
Measuring from center tap like the tube voltages show. Cap 127 is isolated from ground. Cap 127 shown in upper left of p...dconant — 08:05 AM
My Philco 37-116 Restore
Are you measuring relative to the centertap or the GND?morzh — 11:57 PM
Philco 610B oscillator wiring
Still not clear on the wiring interface between the 6A7 and oscillator. After refering to the available schematics and s...Tubester — 07:18 PM
Refinishing Ideas
My 37-116 code 121 is the best sounding radio i have...a daily driver. Since we are talking about "changes". ...poulsbobill — 07:18 PM
My Philco 37-116 Restore
Hello, I finally got brave enough to take the cans off the Expander Unit. Got the grid cap wires replaced and back toget...dconant — 06:50 PM
Zenith H725
I got into the first AM IF can today, and found its mica was cracked. Amazing that it was still working. This one makes ...EdHolland — 06:10 PM
Philco model #20
AHH HA , I got it and can’t thank you fellows enough , when I changed the capacitors I took the advice and did not unsol...onlyrick — 02:24 PM
Zenith H725
Hello Ed, yes, I like letting projects run for few days to make sure they don't start acting up . Sincerely Richardradiorich — 01:03 PM

[-]
Who's Online
There are currently 811 online users. [Complete List]
» 1 Member(s) | 810 Guest(s)
Avatar

>