Starting on Philco 90

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Starting on Philco 90

KCMike
Phorum Expert

Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.

11-12-2014, 04:57 PM

Thanks morzh and Mondial. The micas on the trimmers is what I was concerned with.
The cap is fairly dirty under the plates, but I will try the light brushing and air first.
There is some rust on the upper edges of some of the rotor plates that goes maybe 1/4".
Should I just leave that alone?

Find

« Next Oldest | Next Newest »

Messages In This Thread

Starting on Philco 90 - by KCMike - 11-12-2014, 01:07 PM

RE: Starting on Philco 90 - by morzh - 11-12-2014, 02:37 PM

RE: Starting on Philco 90 - by Mondial - 11-12-2014, 04:35 PM

RE: Starting on Philco 90 - by KCMike - 11-12-2014, 04:57 PM

RE: Starting on Philco 90 - by morzh - 11-12-2014, 05:02 PM

RE: Starting on Philco 90 - by KCMike - 11-16-2014, 07:15 PM

RE: Starting on Philco 90 - by Ron Ramirez - 11-16-2014, 09:51 PM

RE: Starting on Philco 90 - by KCMike - 11-20-2014, 05:09 PM

RE: Starting on Philco 90 - by morzh - 11-20-2014, 05:15 PM

RE: Starting on Philco 90 - by KCMike - 11-20-2014, 06:03 PM

RE: Starting on Philco 90 - by jerryhawthorne - 11-20-2014, 07:07 PM

RE: Starting on Philco 90 - by KCMike - 11-20-2014, 07:16 PM

RE: Starting on Philco 90 - by morzh - 11-20-2014, 08:20 PM

RE: Starting on Philco 90 - by Steve Davis - 11-21-2014, 08:03 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 6032 online users. [Complete List]
» 1 Member(s) | 6031 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me