1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Feeling the current ....
morzh
Odobenus rosmarus
*****
Posts: 15,811
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
#19

11-15-2014, 05:16 PM
GFI is probably the best protection, povided it is wired correctly and tested regularly.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Feeling the current .... - by ODPILOT - 11-09-2014, 07:50 PM
RE: Feeling the current .... - by Mondial - 11-09-2014, 08:22 PM
RE: Feeling the current .... - by morzh - 11-09-2014, 08:42 PM
RE: Feeling the current .... - by ODPILOT - 11-09-2014, 09:13 PM
RE: Feeling the current .... - by Arran - 11-10-2014, 01:31 AM
RE: Feeling the current .... - by morzh - 11-10-2014, 10:15 AM
RE: Feeling the current .... - by ODPILOT - 11-10-2014, 09:22 PM
RE: Feeling the current .... - by ODPILOT - 11-10-2014, 09:24 PM
RE: Feeling the current .... - by morzh - 11-10-2014, 11:33 PM
RE: Feeling the current .... - by mikethedruid - 11-11-2014, 06:17 AM
RE: Feeling the current .... - by PAradiogeek - 11-11-2014, 07:36 AM
RE: Feeling the current .... - by morzh - 11-11-2014, 12:16 PM
RE: Feeling the current .... - by ODPILOT - 11-11-2014, 02:17 PM
RE: Feeling the current .... - by morzh - 11-11-2014, 02:32 PM
RE: Feeling the current .... - by ODPILOT - 11-12-2014, 07:24 PM
RE: Feeling the current .... - by morzh - 11-12-2014, 08:00 PM
RE: Feeling the current .... - by Arran - 11-14-2014, 03:25 AM
RE: Feeling the current .... - by codefox1 - 11-15-2014, 04:39 PM
RE: Feeling the current .... - by morzh - 11-15-2014, 05:16 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5302 online users. [Complete List]
» 1 Member(s) | 5301 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration