1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 16B
Arran
Phorum Expert
*****
Posts: 4,708
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#16

11-16-2014, 03:27 AM
 What does the pull out knob, speed reduction mechanism, look like? Is it similar to the RCA/G.E ones from 1933-35 with a claw that grabs a disk when you push it in for high speed tuning?
Regards
Arran
(This post was last modified: 11-16-2014, 03:56 AM by Arran.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 16B - by 37silverstreak - 11-08-2014, 04:12 PM
RE: Philco 16B - by morzh - 11-08-2014, 04:17 PM
RE: Philco 16B - by Eric Adams - 11-08-2014, 05:17 PM
RE: Philco 16B - by klondike98 - 11-08-2014, 05:31 PM
RE: Philco 16B - by jerryhawthorne - 11-08-2014, 05:45 PM
RE: Philco 16B - by radiohenry - 11-08-2014, 11:55 PM
RE: Philco 16B - by thirtiesradio - 11-09-2014, 02:03 AM
RE: Philco 16B - by PhilcoJohn - 11-09-2014, 06:23 AM
RE: Philco 16B - by Arran - 11-11-2014, 01:13 AM
RE: Philco 16B - by Ron Ramirez - 11-11-2014, 07:43 AM
RE: Philco 16B - by Arran - 11-14-2014, 01:22 AM
RE: Philco 16B - by Allen in SB - 11-14-2014, 02:01 AM
RE: Philco 16B - by Ron Ramirez - 11-14-2014, 08:47 AM
RE: Philco 16B - by 37silverstreak - 11-15-2014, 12:45 PM
RE: Philco 16B - by Geoff - 11-15-2014, 01:41 PM
RE: Philco 16B - by Arran - 11-16-2014, 03:27 AM
RE: Philco 16B - by Ron Ramirez - 11-16-2014, 07:54 AM
RE: Philco 16B - by Arran - 11-17-2014, 01:25 AM
RE: Philco 16B - by thirtiesradio - 12-12-2014, 11:58 AM
RE: Philco 16B - by Jayce - 12-19-2014, 12:44 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM

[-]
Who's Online
There are currently 4309 online users. [Complete List]
» 1 Member(s) | 4308 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios