Silvertone model 1953

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Silvertone model 1953

Mondial
Phorum Expert

Posts: 1,114
Threads: 14
Joined: Feb 2013
City: Irvington, NY

#24

11-18-2014, 12:30 AM

These rectifier diodes would work fine. They are rated at 1 Amp and 1000 Volts reverse, which is more than adequate and they can be used for other uses as well:

http://www.ebay.com/itm/10pcs-1N4007-1A-...7580&rt=nc

You want the diode in series with only the filaments, not the plates of the 25Z5. Actually it will work that way, but if the diode polarity is reversed you will get no DC out of the rectifier tube.

(This post was last modified: 11-18-2014, 12:35 AM by Mondial.)

Find

« Next Oldest | Next Newest »

Messages In This Thread

Silvertone model 1953 - by Art Hoch - 10-21-2014, 12:32 PM

RE: Silvertone model 1953 - by morzh - 10-21-2014, 02:16 PM

RE: Silvertone model 1953 - by Art Hoch - 10-23-2014, 11:30 AM

RE: Silvertone model 1953 - by morzh - 10-23-2014, 11:45 AM

RE: Silvertone model 1953 - by Radioroslyn - 11-02-2014, 09:08 PM

RE: Silvertone model 1953 - by morzh - 11-02-2014, 09:21 PM

RE: Silvertone model 1953 - by Mondial - 11-02-2014, 09:51 PM

RE: Silvertone model 1953 - by Art Hoch - 11-09-2014, 05:24 PM

RE: Silvertone model 1953 - by Art Hoch - 11-12-2014, 11:19 AM

RE: Silvertone model 1953 - by morzh - 11-12-2014, 12:24 PM

RE: Silvertone model 1953 - by Art Hoch - 11-13-2014, 09:30 PM

RE: Silvertone model 1953 - by Mondial - 11-14-2014, 12:07 AM

RE: Silvertone model 1953 - by Art Hoch - 11-14-2014, 11:25 AM

RE: Silvertone model 1953 - by Art Hoch - 11-15-2014, 11:41 AM

RE: Silvertone model 1953 - by morzh - 11-15-2014, 11:46 AM

RE: Silvertone model 1953 - by Art Hoch - 11-15-2014, 01:07 PM

RE: Silvertone model 1953 - by morzh - 11-15-2014, 03:38 PM

RE: Silvertone model 1953 - by Art Hoch - 11-17-2014, 01:14 PM

RE: Silvertone model 1953 - by Radioroslyn - 11-17-2014, 02:28 PM

RE: Silvertone model 1953 - by morzh - 11-17-2014, 02:38 PM

RE: Silvertone model 1953 - by Art Hoch - 11-17-2014, 05:42 PM

RE: Silvertone model 1953 - by Mondial - 11-17-2014, 10:18 PM

RE: Silvertone model 1953 - by Art Hoch - 11-17-2014, 11:41 PM

RE: Silvertone model 1953 - by Mondial - 11-18-2014, 12:30 AM

RE: Silvertone model 1953 - by Arran - 11-18-2014, 06:22 AM

RE: Silvertone model 1953 - by Art Hoch - 12-02-2014, 09:35 PM

RE: Silvertone model 1953 - by Arran - 12-03-2014, 03:33 AM

RE: Silvertone model 1953 - by Radioroslyn - 12-02-2014, 10:31 PM

RE: Silvertone model 1953 - by Art Hoch - 12-03-2014, 10:40 AM

RE: Silvertone model 1953 - by Art Hoch - 12-06-2014, 12:28 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me