1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
40-165 Tube layout label
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#13

11-19-2014, 08:39 AM
I had to use Photoshop (CS5) for the "PHILCO" and "REG. U.S. PAT.OFF." at the top, because the letters needed to have small spaces between them and that is a trick I cannot do in Paint Shop Pro. For the rest, I used my old but handy Paint Shop Pro 4.14 which is 17 year old software but still runs in Windows 8.1.
--
Ron Ramirez
Ferdinand IN
Find
« Next Oldest | Next Newest »


Messages In This Thread
40-165 Tube layout label - by keith49vj3 - 11-16-2014, 12:13 PM
RE: 40-165 Tube layout label - by keith49vj3 - 11-17-2014, 08:14 PM
RE: 40-165 Tube layout label - by Ron Ramirez - 11-17-2014, 09:41 PM
RE: 40-165 Tube layout label - by morzh - 11-17-2014, 10:57 PM
RE: 40-165 Tube layout label - by Ron Ramirez - 11-18-2014, 08:12 AM
RE: 40-165 Tube layout label - by keith49vj3 - 11-18-2014, 09:00 AM
RE: 40-165 Tube layout label - by Ron Ramirez - 11-18-2014, 09:08 AM
RE: 40-165 Tube layout label - by keith49vj3 - 11-18-2014, 02:15 PM
RE: 40-165 Tube layout label - by Ron Ramirez - 11-18-2014, 02:45 PM
RE: 40-165 Tube layout label - by morzh - 11-18-2014, 03:51 PM
RE: 40-165 Tube layout label - by keith49vj3 - 11-18-2014, 10:46 PM
RE: 40-165 Tube layout label - by morzh - 11-18-2014, 11:12 PM
RE: 40-165 Tube layout label - by Ron Ramirez - 11-19-2014, 08:39 AM
RE: 40-165 Tube layout label - by Ron Ramirez - 11-19-2014, 09:43 AM
RE: 40-165 Tube layout label - by Arran - 11-19-2014, 02:39 PM
RE: 40-165 Tube layout label - by Mondial - 11-19-2014, 03:30 PM
RE: 40-165 Tube layout label - by keith49vj3 - 11-19-2014, 09:05 PM
RE: 40-165 Tube layout label - by Ron Ramirez - 11-19-2014, 10:31 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 16B Parts
The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM
Philco 38-7 Speaker
I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration