1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Model 43 - Speaker re-coning
jhgrahamjr
Junior Member
**
Posts: 47
Threads: 12
Joined: Nov 2014
City: Calimesa, CA
#1

11-24-2014, 02:04 PM
Can anyone recommend a competent craftsman to re-cone the speaker in a Model 43 cathedral style radio?

I found some references to Hank Brazeal, but the phone number and email address don't work.

Thanks!
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Model 43 - Speaker re-coning - by jhgrahamjr - 11-24-2014, 02:04 PM
RE: Model 43 - Speaker re-coning - by morzh - 11-24-2014, 02:41 PM
RE: Model 43 - Speaker re-coning - by klondike98 - 11-24-2014, 03:13 PM
RE: Model 43 - Speaker re-coning - by klondike98 - 11-24-2014, 04:09 PM
RE: Model 43 - Speaker re-coning - by jhgrahamjr - 11-24-2014, 05:52 PM
RE: Model 43 - Speaker re-coning - by jhgrahamjr - 11-24-2014, 10:23 PM
RE: Model 43 - Speaker re-coning - by Eric Adams - 11-25-2014, 12:44 AM
RE: Model 43 - Speaker re-coning - by jhgrahamjr - 11-25-2014, 12:22 PM
RE: Model 43 - Speaker re-coning - by PAradiogeek - 11-26-2014, 02:09 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM
Zenith H725
When dealing with noise on power lines, time to get my Jackery 240 out. Talk about clean can hold a portable am radio ne...David — 08:52 PM
Zenith H725
Arran - I bet you're right probably vinyl, there was no rubber smell when desoldering it, which you often get with the o...EdHolland — 08:23 PM
Zenith H725
Ed; It was very likely vinyl covered wire given the vintage of the set, there was some rubber/gutta percha wire used ...Arran — 06:34 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration