Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

New to Phorum and a Philco 38
#8

I have had some time to look at the 38 more closely, here is what I know so far;

As I mentioned above, a conversion had been done to allow the radio to operate on AC, but the transformer failed and the previous owner removed it.

Two tube sockets have been removed, type 6 and type 30.
Other tubes
Type 19 replaced with a tube with no markings
Type 15 replaced with 6A8 G
Type 32 replaced with 75
Type 32 replaced with 78

With the exception of type 19, all other tube sockets have been replaced.
A multi section electrolytic has been added
Holes have been drilled for TX, along with some other miscellaneous holes
Has "newer" wire and some caps

I have some pictures, and will set up an account online so they can be viewed in the next couple of days.

Russ


Messages In This Thread
New to Phorum and a Philco 38 - by radioalfa - 11-22-2014, 11:49 PM
RE: New to Phorum and a Philco 38 - by sam - 11-23-2014, 02:19 AM
RE: New to Phorum and a Philco 38 - by Arran - 11-23-2014, 05:14 AM
RE: New to Phorum and a Philco 38 - by morzh - 11-23-2014, 11:24 AM
RE: New to Phorum and a Philco 38 - by klondike98 - 11-23-2014, 11:35 AM
RE: New to Phorum and a Philco 38 - by radioalfa - 11-23-2014, 12:57 PM
RE: New to Phorum and a Philco 38 - by radioalfa - 11-24-2014, 11:04 PM
RE: New to Phorum and a Philco 38 - by Arran - 11-25-2014, 04:38 AM
RE: New to Phorum and a Philco 38 - by radioalfa - 11-25-2014, 11:28 PM
RE: New to Phorum and a Philco 38 - by Arran - 11-26-2014, 02:00 AM
RE: New to Phorum and a Philco 38 - by radioalfa - 11-26-2014, 09:15 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM

[-]
Who's Online
There are currently no members online.

>