1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
37-675 Dial
AI2V
Member
***
Posts: 201
Threads: 26
Joined: Dec 2005
City: Morris Plains, NJ
#3

12-01-2014, 05:56 PM
The light from pretty much any LED is broad; the light from the original incandescent bulb is a very tiny, concentrated light source. Hence the display with an LED will be very broad and spread after it goes through the lens but the old fashioned bulb will "shine" with a good, sharp line. Been there, done that.
Pete AI2V
Find
« Next Oldest | Next Newest »


Messages In This Thread
37-675 Dial - by w4rtc - 11-24-2014, 06:35 PM
RE: 37-675 Dial - by morzh - 11-24-2014, 09:37 PM
RE: 37-675 Dial - by AI2V - 12-01-2014, 05:56 PM
RE: 37-675 Dial - by morzh - 12-01-2014, 06:57 PM
RE: 37-675 Dial - by w4rtc - 12-01-2014, 10:32 PM
RE: 37-675 Dial - by morzh - 12-02-2014, 12:48 AM
RE: 37-675 Dial - by w4rtc - 12-02-2014, 01:33 AM
RE: 37-675 Dial - by morzh - 12-02-2014, 10:51 AM
RE: 37-675 Dial - by morzh - 12-02-2014, 10:40 PM
RE: 37-675 Dial - by Ron Ramirez - 12-02-2014, 11:02 PM
RE: 37-675 Dial - by AI2V - 12-06-2014, 05:46 PM
RE: 37-675 Dial - by w4rtc - 12-06-2014, 09:19 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5860 online users. [Complete List]
» 2 Member(s) | 5858 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration