1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
37-11 Dial mechanism questions
doug-5er
Junior Member
**
Posts: 40
Threads: 6
Joined: Aug 2014
City: Lakewood, Ca 90713
#4

12-08-2014, 09:03 PM
Hi Mike,
I  have been working on my 38-2 same dial and have become almost a master at taking the SOB apart and back together again.Are you missing the spring part 16 on the schematic Ron posted? It is not a coil spring persay just a thin bent piece of metal.  
(This post was last modified: 12-08-2014, 09:37 PM by doug-5er.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
37-11 Dial mechanism questions - by k9uw - 12-02-2014, 01:22 AM
RE: 37-11 Dial mechanism questions - by sam - 12-02-2014, 04:46 AM
RE: 37-11 Dial mechanism questions - by doug-5er - 12-08-2014, 09:03 PM
RE: 37-11 Dial mechanism questions - by k9uw - 12-08-2014, 09:40 PM
RE: 37-11 Dial mechanism questions - by doug-5er - 12-08-2014, 11:04 PM
RE: 37-11 Dial mechanism questions - by k9uw - 12-09-2014, 12:00 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5588 online users. [Complete List]
» 1 Member(s) | 5587 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration