Philco 37-61 problems

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Guest
Unregistered

11-27-2008, 11:30 AM

Checked to ground, had to unsolder a wire on the secondary and unhook the "link" on the antenna connection "panel" but all tested ok. What about the AVC? I think that is the wire that I had to unsolder, could the avc do ant thing to just one end of the dial?
Tom

« Next Oldest | Next Newest »

Messages In This Thread

Philco 37-61 problems - by Guest - 11-26-2008, 09:43 PM

Re: Philco 37-61 problems - by exray - 11-27-2008, 07:43 AM

Re: Philco 37-61 problems - by Guest - 11-27-2008, 09:01 AM

Re: Philco 37-61 problems - by exray - 11-27-2008, 09:15 AM

Re: Philco 37-61 problems - by Guest - 11-27-2008, 10:05 AM

Re: Philco 37-61 problems - by exray - 11-27-2008, 10:29 AM

Re: Philco 37-61 problems - by Guest - 11-27-2008, 11:07 AM

Re: Philco 37-61 problems - by Guest - 11-27-2008, 11:30 AM

Re: Philco 37-61 problems - by Guest - 11-27-2008, 12:16 PM

Re: Philco 37-61 problems - by exray - 11-27-2008, 12:21 PM

Re: Philco 37-61 problems - by Guest - 11-27-2008, 05:26 PM

Re: Philco 37-61 problems - by exray - 11-27-2008, 07:45 PM

Re: Philco 37-61 problems - by wonderwrench - 11-27-2008, 08:04 PM

Re: Philco 37-61 problems - by exray - 11-27-2008, 08:31 PM

Re: Philco 37-61 problems - by Guest - 11-27-2008, 10:03 PM

Re: Philco 37-61 problems - by Guest - 11-29-2008, 06:04 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online

There are currently 5100 online users. [Complete List]
» 2 Member(s) | 5098 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me