1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
46-1203 restoration
Jrod7711
Junior Member
**
Posts: 4
Threads: 1
Joined: Dec 2014
City: Illinois
#1

12-09-2014, 03:31 PM
I have been doing reasearc on my radio and found out that it is in better condition than I speculated. With this knowledge I believe I might be able to get the phonograph working, however I can't find much information on the radio. I found some schematics but I don't know how to read them. I read that my model has a crystal cartridge which by now is most likely "dead". I can't find a manual or step-by-step instructions helping me to take the insides apart and removing the cartridge. Does anyone know anything about how to take these apart? If so can you please help me.
Thank you.
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
46-1203 restoration - by Jrod7711 - 12-09-2014, 03:31 PM
RE: 46-1203 restoration - by morzh - 12-09-2014, 04:55 PM
RE: 46-1203 restoration - by Jrod7711 - 12-09-2014, 05:21 PM
RE: 46-1203 restoration - by klondike98 - 12-09-2014, 05:43 PM
RE: 46-1203 restoration - by Jrod7711 - 12-09-2014, 05:56 PM
RE: 46-1203 restoration - by Ron Ramirez - 12-09-2014, 10:27 PM
RE: 46-1203 restoration - by Jrod7711 - 12-09-2014, 11:41 PM
RE: 46-1203 restoration - by klondike98 - 12-10-2014, 11:48 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM
Zenith H725
When dealing with noise on power lines, time to get my Jackery 240 out. Talk about clean can hold a portable am radio ne...David — 08:52 PM
Zenith H725
Arran - I bet you're right probably vinyl, there was no rubber smell when desoldering it, which you often get with the o...EdHolland — 08:23 PM
Zenith H725
Ed; It was very likely vinyl covered wire given the vintage of the set, there was some rubber/gutta percha wire used ...Arran — 06:34 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration