Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 37-61 problems
#11

Bill, the rf section of the tuner did check out ok, sorry I did not get back on that one. I checked it with a meter and it is not shorted and it is 360mmf fully closed. On the antenna, I have been swaping between a long wire strung up in the rafters and a wire that goes around the rear inside of the framing of the radio,it is a console model. The wire up in the rafters performs better but not much. Now this is downstairs and the rafters are the floor of the ground floor, about 2 feet above ground level. Once, I took the radio upstairs to see if that would help-no better. On the topic of antennas, on the schematic it says that it should have a "high-efficiency" aerial and that the "transmission lines" go to terminals 1&2. Do you have any idea what that is?
Tom


Messages In This Thread
Philco 37-61 problems - by Guest - 11-26-2008, 09:43 PM
Re: Philco 37-61 problems - by exray - 11-27-2008, 07:43 AM
Re: Philco 37-61 problems - by Guest - 11-27-2008, 09:01 AM
Re: Philco 37-61 problems - by exray - 11-27-2008, 09:15 AM
Re: Philco 37-61 problems - by Guest - 11-27-2008, 10:05 AM
Re: Philco 37-61 problems - by exray - 11-27-2008, 10:29 AM
Re: Philco 37-61 problems - by Guest - 11-27-2008, 11:07 AM
Re: Philco 37-61 problems - by Guest - 11-27-2008, 11:30 AM
Re: Philco 37-61 problems - by Guest - 11-27-2008, 12:16 PM
Re: Philco 37-61 problems - by exray - 11-27-2008, 12:21 PM
Re: Philco 37-61 problems - by Guest - 11-27-2008, 05:26 PM
Re: Philco 37-61 problems - by exray - 11-27-2008, 07:45 PM
Re: Philco 37-61 problems - by wonderwrench - 11-27-2008, 08:04 PM
Re: Philco 37-61 problems - by exray - 11-27-2008, 08:31 PM
Re: Philco 37-61 problems - by Guest - 11-27-2008, 10:03 PM
Re: Philco 37-61 problems - by Guest - 11-29-2008, 06:04 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently no members online.

>